Seyedeh Mahsa Sheikh-Al-Eslamian1, Narges Panahandeh1, Ahmad Najafi-Abrandabadi1, Elham Hasani1, Hassan Torabzadeh2, Amir Ghassemi3. 1. Dental Research Center, Research Institute of Dental Sciences, Dental School, Shahid Beheshti University of Medical Sciences, Tehran, Iran. 2. Iranian Center for Endodontic Research, Research Institute of Dental Sciences, Dental School, Shahid Beheshti University of Medical Sciences, Tehran, Iran. 3. Preventive Dentistry Research Center, Research Institute of Dental Sciences, Dental School, Shahid Beheshti University of Medical Sciences, Tehran, Iran.
Abstract
AIM: The aim of the present study was to evaluate the micro-shear bond strength of silorane-based composites after saliva/blood decontamination. METHODS: A transparent mold (1 × 2 × 1 cm) was used to make 11 flat, silorane-based composite blocks. One block served as the control. After contamination, the blocks were treated as follows: group 1: 10-s air spray; group 2: 10-s water spray + 10-s air spray; group 3: 10-s water spray + 10-s air spray + 10-s etching with phosphoric acid; group 4: 10-s air spray + 10-s etching + bonding; group 5: 10-s water spray + 10-s air spray + 10-s etching + bonding; and groups 6-10: treated the same as groups 1-5, the only difference being that blood was used instead of saliva. Ten tubes (0.7 mm × 1 mm) containing silorane-based composites were attached to each decontaminated block and light cured for 40 s. After 24-h storage in distilled water, specimens were tested under micro-shear loading at a cross-head speed of 0.5 mm/min. Data were analyzed using one-way anova and Tukey's honest significant difference (HSD) test (P < 0.05). RESULTS: One-way anova showed significant differences in the micro-shear bond strength among the experimental groups (P < 0.001). Tukey's HSD test revealed that the bond strengths in groups 5, 9, and 10 were similar to the control group (P > 0.05). CONCLUSION: Decontamination by water and air spray, etching, and bonding was effective in restoring the bond strength of silorane-based composite increments.
AIM: The aim of the present study was to evaluate the micro-shear bond strength of silorane-based composites after saliva/blood decontamination. METHODS: A transparent mold (1 × 2 × 1 cm) was used to make 11 flat, silorane-based composite blocks. One block served as the control. After contamination, the blocks were treated as follows: group 1: 10-s air spray; group 2: 10-s water spray + 10-s air spray; group 3: 10-s water spray + 10-s air spray + 10-s etching with phosphoric acid; group 4: 10-s air spray + 10-s etching + bonding; group 5: 10-s water spray + 10-s air spray + 10-s etching + bonding; and groups 6-10: treated the same as groups 1-5, the only difference being that blood was used instead of saliva. Ten tubes (0.7 mm × 1 mm) containing silorane-based composites were attached to each decontaminated block and light cured for 40 s. After 24-h storage in distilled water, specimens were tested under micro-shear loading at a cross-head speed of 0.5 mm/min. Data were analyzed using one-way anova and Tukey's honest significant difference (HSD) test (P < 0.05). RESULTS: One-way anova showed significant differences in the micro-shear bond strength among the experimental groups (P < 0.001). Tukey's HSD test revealed that the bond strengths in groups 5, 9, and 10 were similar to the control group (P > 0.05). CONCLUSION: Decontamination by water and air spray, etching, and bonding was effective in restoring the bond strength of silorane-based composite increments.