Literature DB >> 26322646

Joint Effects of Photoactive TiO2 and Fluoride-Doping on SnO2 Inverse Opal Nanoarchitecture for Solar Water Splitting.

Yun Gun1, Gwang Yeom Song2, Vu Hong Vinh Quy3, Jaeyeong Heo2, Hyunjung Lee4, Kwang-Soon Ahn3, Soon Hyung Kang5.   

Abstract

Inverse opal (IO) films of tin dioxide (SnO2) were fabricated on polystyrene (PS) beads (diameter=350 nm (±20 nm) with a spin coating method. To compensate for the large band gap (Eg=3.8 eV), a thin TiO2 shell was deposited on the SnO2-IO films with atomic layer deposition (ALD), which produced shells with thicknesses of 10-40 nm. The morphological changes and crystalline properties of the SnO2 and TiO2-coated SnO2 (herein after referred to as TiO2/SnO2) IO films were investigated with field-emission scanning electron microscopy and X-ray diffraction, respectively. The photoelectrochemical (PEC) behavior of the samples was tested in a 0.1 M KOH solution under 1 sun illumination (100 mW/cm2 with an AM 1.5 filter). The highest PEC performance was obtained with the TiO2(10 nm)/SnO2 IO films, which produced a photocurrent density (Jsc) of 4.67 mA/cm2 at 0.5 V (vs NHE) and was sequentially followed by the TiO2(20 nm)/SnO2-IO, TiO2(30 nm)/SnO2-IO, TiO2 (40 nm)/SnO2-IO and SnO2 IO films. Overall, the thin TiO2 shell covered on the SnO2-IO core enhanced Jsc by 3 orders of magnitude, which in turn the PEC activity. This is mainly ascribed to the extremely low charge-transfer resistance (Rct) in the photoelectrode/electrolyte and at the TiO2/SnO2 interface, as well as the contribution of the photoactive TiO2 layer, which has an Eg of 3.2 eV. Moreover, to improve the electrical conductivity of the core SnO2 IO film, the films were doped with 10 mol % of F. The F- doped films were labeled as the FTO IO film. The Rct of the FTO-IO films decreased because of the improved electronic conductivity, enhancing the PEC performance of the TiO2(10 nm)/FTO-IO films by approximately 20%. The core-shell nanowire mesh nanoarchitecture is therefore suggested to provide an insight for designing the peculiar structure based on the material's properties and the engineering of their band gap energy for highly efficient PEC performance.

Entities:  

Keywords:  F doped SnO2; SnO2; TiO2; atomic layer deposition; core−shell inverse opals; photoelectrochemical water splitting

Year:  2015        PMID: 26322646     DOI: 10.1021/acsami.5b05914

Source DB:  PubMed          Journal:  ACS Appl Mater Interfaces        ISSN: 1944-8244            Impact factor:   9.229


  4 in total

1.  2D and 3D photonic crystal materials for photocatalysis and electrochemical energy storage and conversion.

Authors:  Gillian Collins; Eileen Armstrong; David McNulty; Sally O'Hanlon; Hugh Geaney; Colm O'Dwyer
Journal:  Sci Technol Adv Mater       Date:  2016-09-16       Impact factor: 8.090

2.  Novel multilayer TiO2 heterojunction decorated by low g-C3N4 content and its enhanced photocatalytic activity under UV, visible and solar light irradiation.

Authors:  Yizheng Wang; Jiang Yu; Weidong Peng; Jing Tian; Chun Yang
Journal:  Sci Rep       Date:  2019-04-11       Impact factor: 4.379

Review 3.  Host/Guest Nanostructured Photoanodes Integrated with Targeted Enhancement Strategies for Photoelectrochemical Water Splitting.

Authors:  Zhiwei Wang; Heng Zhu; Wenguang Tu; Xi Zhu; Yingfang Yao; Yong Zhou; Zhigang Zou
Journal:  Adv Sci (Weinh)       Date:  2021-11-05       Impact factor: 16.806

4.  Sn-doped 3D ATO inverse opal/hematite hierarchical structures: facile fabrication and efficient photoelectrochemical performance.

Authors:  Junjie Zhang; Jing Li; Boxue Zhang; Jianfeng Ye; Yun Wang; Xiaozhou Ye
Journal:  RSC Adv       Date:  2018-12-18       Impact factor: 4.036

  4 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.