Emanuela Marcelli1, Maria Laura Costantino2, Tomaso Villa3, Paola Bagnoli4, Romano Zannoli5, Ivan Corazza6, Laura Cercenelli7. 1. Associate Professor, Experimental Diagnostic and Specialty Medicine Department, University of Bologna, Bologna, Italy. Electronic address: emanuela.marcelli@unibo.it. 2. Full Professor, Laboratory of Biological Structure Mechanics, Department of Chemistry, Materials and Chemical Engineering "Giulio Natta," Polytechnic University of Milan, Milan, Italy. 3. Assistant Professor, Laboratory of Biological Structure Mechanics, Department of Chemistry, Materials and Chemical Engineering "Giulio Natta," Polytechnic University of Milan; Istituti di Ricovero e Cura a Carattere Scientifico, Istituto Ortopedico Galeazzi, Milan, Italy. 4. Postdoctoral Fellow, Laboratory of Biological Structure Mechanics, Department of Chemistry, Materials and Chemical Engineering "Giulio Natta," Polytechnic University of Milan, Milan, Italy. 5. Full Professor, Experimental Diagnostic and Specialty Medicine Department, University of Bologna, Bologna, Italy. 6. Assistant Professor, Experimental Diagnostic and Specialty Medicine Department, University of Bologna, Bologna, Italy. 7. Postdoctoral Fellow, Experimental Diagnostic and Specialty Medicine Department, University of Bologna, Bologna, Italy.
Abstract
STATEMENT OF PROBLEM: Metal ceramic systems are used for the majority of dental crowns and fixed dental prostheses. However, problems with porcelain bonding are encountered when titanium is used as the substrate. PURPOSE: The purpose of this study was to evaluate the effect of intermediate calcium oxide-stabilized zirconia (ZrO2-CaO) coatings deposited by cold thermal spraying on the titanium-porcelain bonding in dental restorations. MATERIAL AND METHODS: Two different types of ZrO2-CaO coatings obtained by oxyacetylene cold thermal spraying deposition were applied on commercially pure titanium bars before adding the porcelain layer. Type 1 was obtained by directly spraying the ZrO2-CaO powder on the titanium substrate. Type 2 was obtained by spraying a bond coat of nickel-aluminum-molybdenum alloy before spraying the ZrO2-CaO powder. Three-point bend tests according to International Organization of Standardization 9693-1:2012 were carried out to evaluate the debonding strength for the ZrO2-CaO-coated specimens (types 1 and 2) in comparison with a noncoated group (control), which received a traditional bonder-based adhesive technique. The results were compared with ANOVA, followed by the Student-Newman-Keuls test for pairwise comparisons. Scanning electron microscopy and energy dispersion spectroscopy were used to examine the interfacial properties and the failure mode of each group. RESULTS: Mean (±standard deviation) debonding strength values for type 1 coating (25.97 ±2.53 MPa) and control (23.51 ±2.94 MPa) were near the acceptable lower limit of 25 MPa indicated by the International Organization of Standardization 9693-1:2012 and were not significantly different (Student-Newman-Keuls test, P>.05). Type 2 coating produced an improved titanium-porcelain bonding (debonding strength=39.47 ±4.12 MPa), significantly higher than both type 1 (Student-Newman-Keuls test, P<.05) and control (Student-Newman-Keuls test, P<.05). Scanning electron microscopy-energy dispersion spectroscopy analysis confirmed these findings, which revealed a predominant cohesive failure mode for type 2. CONCLUSIONS: An intermediate coating layer of ZrO2-CaO plus a substrate of bonding nickel-aluminum-molybdenum alloy applied by oxyacetylene cold thermal spraying deposition provided an improved titanium-porcelain bond.
STATEMENT OF PROBLEM: Metal ceramic systems are used for the majority of dental crowns and fixed dental prostheses. However, problems with porcelain bonding are encountered when titanium is used as the substrate. PURPOSE: The purpose of this study was to evaluate the effect of intermediate calcium oxide-stabilized zirconia (ZrO2-CaO) coatings deposited by cold thermal spraying on the titanium-porcelain bonding in dental restorations. MATERIAL AND METHODS: Two different types of ZrO2-CaO coatings obtained by oxyacetylene cold thermal spraying deposition were applied on commercially pure titanium bars before adding the porcelain layer. Type 1 was obtained by directly spraying the ZrO2-CaO powder on the titanium substrate. Type 2 was obtained by spraying a bond coat of nickel-aluminum-molybdenum alloy before spraying the ZrO2-CaO powder. Three-point bend tests according to International Organization of Standardization 9693-1:2012 were carried out to evaluate the debonding strength for the ZrO2-CaO-coated specimens (types 1 and 2) in comparison with a noncoated group (control), which received a traditional bonder-based adhesive technique. The results were compared with ANOVA, followed by the Student-Newman-Keuls test for pairwise comparisons. Scanning electron microscopy and energy dispersion spectroscopy were used to examine the interfacial properties and the failure mode of each group. RESULTS: Mean (±standard deviation) debonding strength values for type 1 coating (25.97 ±2.53 MPa) and control (23.51 ±2.94 MPa) were near the acceptable lower limit of 25 MPa indicated by the International Organization of Standardization 9693-1:2012 and were not significantly different (Student-Newman-Keuls test, P>.05). Type 2 coating produced an improved titanium-porcelain bonding (debonding strength=39.47 ±4.12 MPa), significantly higher than both type 1 (Student-Newman-Keuls test, P<.05) and control (Student-Newman-Keuls test, P<.05). Scanning electron microscopy-energy dispersion spectroscopy analysis confirmed these findings, which revealed a predominant cohesive failure mode for type 2. CONCLUSIONS: An intermediate coating layer of ZrO2-CaO plus a substrate of bonding nickel-aluminum-molybdenum alloy applied by oxyacetylene cold thermal spraying deposition provided an improved titanium-porcelain bond.