Transistor application of alkyl-substituted picene.

Field-effect transistors (FETs) were fabricated with a thin film of 3,10-ditetradecylpicene, picene-(C14H29)2, formed using either a thermal deposition or a deposition from solution (solution process). All FETs showed p-channel normally-off characteristics. The field-effect mobility, μ, in a picene-(C14H29)2 thin-film FET with PbZr0.52Ti0.48O3 (PZT) gate dielectric reached ~21 cm2 V(-1) s(-1), which is the highest μ value recorded for organic thin-film FETs; the average μ value (<μ>) evaluated from twelve FET devices was 14(4) cm2 V(-1) s(-1). The <μ> values for picene-(C14H29)2 thin-film FETs with other gate dielectrics such as SiO2, Ta2O5, ZrO2 and HfO2 were greater than 5 cm2 V(-1) s(-1), and the lowest absolute threshold voltage, |Vth|, (5.2 V) was recorded with a PZT gate dielectric; the average |Vth| for PZT gate dielectric is 7(1) V. The solution-processed picene-(C14H29)2 FET was also fabricated with an SiO2 gate dielectric, yielding μ=3.4×10(-2) cm2 V(-1) s(-1). These results verify the effectiveness of picene-(C14H29)2 for electronics applications.

High-performance organic field-effect transistors (FETs) fabricated with various types of organic molecules have desirable characteristics such as light weight, mechanical flexibility, large area coverage, ease of design, and low-energy/low-cost fabrication12345678910111213141516171819202122232425262728. The highest field-effect mobility, μ, is presently 17.2 cm2 V−1 s−1 in thin-film organic FETs29 and 94 cm2 V−1 s−1 in single-crystal organic FETs22. In particular, the promise of [n]phenacene-type molecules ([5]phenacene (picene), [6]phenacene, and [7]phenacene) in transistors is being discussed based on the excellent FET characteristics already observed1314151617. The [n]phenacene molecule has an armchair-shaped molecular structure, and its large band gap and deep valence band suggest that these molecules are chemically stable even in atmospheric conditions1328. Such characteristics are very desirable for transistor applications, as transistors must be durable under repeated use over the long term. However, one of the problems presented by pentacene itself in transistor applications is chemical instability under atmospheric conditions, although pentacene is the organic molecule most commonly used for transistors3456789101112. Therefore, [n]phenacene molecules may be superior to pentacene and its analogues (acene molecules) in transistor applications.

Here, we report the fabrication of an FET device with a new alkyl-substituted picene, and its FET characteristics. A 3,10-ditetradecylpicene (picene-(C14H29)2) thin-film FET shows excellent characteristics, with its highest μ value reaching 21 cm2 V−1 s−1 with a PbZr0.52Ti0.48O3 (PZT) gate dielectric. This may be the highest value reported in an organic thin-film FET to date2930. The solution-deposited-film FET device was fabricated with CHCl3 solvent. Topological characterization of thin films of picene-(C14H29)2 was performed using X-ray diffraction (XRD) and atomic force microscopy (AFM). The structure of the picene-(C14H29)2 molecule and the device structure are shown in Figures 1(a) and (b), respectively.

Figure 1

(a) Molecular structure of picene–(C14H29)2. (b) Structure of picene–(C14H29)2 thin-film FET. (c) XRD pattern of picene–(C14H29)2 thin film and powder. (d) AFM image of picene–(C14H29)2 thin film.

Results

Morphology of picene-(C14H29)2 thin film

The XRD pattern of a picene-(C14H29)2 thin film formed on an SiO2 surface is shown in Figure 1(c), and only a small 001 and a pronounced 100 reflections are observed, implying the absence of parallel planes stacked on the surface. Therefore, this stacking pattern is different from that of thin films of other phenacene molecules, in which the ab-plane is parallel-stacked on the SiO2 surface, because there only 00l reflections are observed16182031. The d100 which refers to the bc-layer spacing can be determined to be 1.368 nm, where the space group is assumed to be the same as that of picene (monoclinic: No. 4, P21). The d001 which refers to the ab-plane spacing was 4.052 nm, which is comparable to the long axis of picene-(C14H29)2, 4.9 nm. Since this distance is too long, the structure may be different from other phenacenes. The inclination angle of picene-(C14H29)2 with respect to the reciprocal lattice c* (|c*| = 1/d001) is estimated to be ~30° which is almost the same as that of other phenacenes16182031. The XRD pattern of a powder sample of picene-(C14H29)2 is shown in Figures 1(c) and 3(b). The a, b, c and β were determined to be 1.3192(8), 0.5516(2), 4.0953(5) nm and 92.67(2)°, respectively, using LeBail fitting. The a and c of the powder are the same as those of a thin film, 1.370 nm and 4.057 nm, respectively, where the β in a thin film is assumed to be the same as that of powder. The crystallite size of thin film is evaluated to be 25 nm, from 100 reflections and the Debye-Scherrer formula; the grain size refers to the 100 direction.

Figure 3

(a) Photograph and (b) XRD patterns of picene-(C14H29)2 thin films formed by solution-deposition. In (b) XRD pattern of powder is also shown. (c) Output and (d) transfer curves of FET with picene-(C14H29)2 thin films formed by solution-deposition. In (d), VD = −100 V. An SiO2 gate dielectric was used. L and W were 100 and 1580 μm.

An AFM image of a picene-(C14H29)2 thin film (60 nm thick) formed by thermal deposition on an SiO2 surface is shown in Figure 1(d). The AFM image shows the presence of grains of 100–1000 nm. The average grain size in the thin film (Figure 1(d)) is 600 nm and the root-mean-square (rms) surface roughness is 28 nm. The average grain size is larger than the 540 nm of picene thin film, while the rms surface roughness is much larger than picene's 3.1 nm16. This may be due to the long axis of the molecule or the presence of long alkyl chains. Judging from the difference between grain size (~600 nm) from the AFM image and crystallite size (~25 nm) from X-ray diffraction, a grain recognized by AFM consists of ~104 crystallites.

FET characteristics of thin-film FET with a picene-(C14H29)2 formed by thermal deposition

The output and transfer curves of a picene-(C14H29)2 thin-film FET with an SiO2 gate dielectric are shown in Figures 2(a) and (b). Typical p-channel FET characteristics are observed in both graphs. The output curves show clear linear and saturation behaviour in low and high absolute drain-voltage, |VD|, regimes, respectively; the drain-voltage, VD, and gate-voltage, VG, applied are negative, since this device operates in p-channel. From this transfer curve at VD = −80 V (saturation regime), the μ, threshold voltage Vth, on-off ratio and sub-threshold swing S are determined to be 3.9 cm2 V−1 s−1, −51 V, 2.2 × 106 and 6.6 V decade−1, respectively.

Figure 2

(a) Output and (b) transfer curves of a picene-(C14H29)2 thin-film FET with SiO2 gate dielectric. Transfer curves of a picene-(C14H29)2 thin-film FET with (c) HfO2 and (d) PZT. In (b), VD = −80 V; in (c) and (d), VD = −20 V. The FETs used for measurements correspond to the sample #1 in each table (Table 1, 2 and 3). L and W were 300 and 500 μm for SiO2, respectively, 450 and 500 μm for HfO2, and 450 and 600 μm for PZT.

The average μ value (<μ>), average Vth (), average on-off ratio (), and average S () from seven picene-(C14H29)2 FETs with SiO2 gate dielectric are 7(2) cm2 V−1 s−1, −30(10) V, 6(4) × 106, and 3(2) V decade−1, respectively. The highest μ value reaches 9.5 cm2 V−1 s−1. Thus, the picene-(C14H29)2 FET shows excellent FET characteristics. All FET parameters in seven FETs are shown in Table 1.

Table 1

FET characteristics of picene-(C14H29)2 thin film FETs with an SiO2 dielectric. W = 500 μm

sample	μ (cm2V−1s−1)	|Vth| (V)	ON/OFF	S (V/decade)	L (μm)
#1	3.9	51.0	2.2 × 106	6.6	300
#2	8.0	26.1	1.5 × 107	2.7	200
#3	7.8	37.6	3.4 × 106	3.6	250
#4	9.5	35.0	6.8 × 106	2.9	300
#5	7.0	28.3	4.6 × 106	2.8	350
#6	6.6	18.8	8.2 × 106	1.9	450
#7	7.0	21.5	5.1 × 106	2.6	450
average	7(2)	30(10)	6(4) × 106	3(2)

Here we briefly comment on the presence of hysteresis (or difference between forward and reverse curves) in transfer and output curves of picene-(C14H29)2 FETs. The hysteresis in picene thin-film FET is previously investigated, which concludes that the hysteresis is closely related to enhancement of trap states (H2O-related trap states) caused by electric field under the presence of H2O at the interface between organic thin-film and gate dielectric1517, i.e., the mechanism is called as bias-stress effect. Therefore, the hysteresis observed in the picene-(C14H29)2 FETs may also be produced by bias-stress effect due to H2O and strong electric-field.

The FET properties were measured after keeping the devices under atmospheric condition or high temperature in order to clarify the durability. The μ values of three picene-(C14H29)2 FETs with SiO2 gate dielectric are evaluated in each experiment. The variation of μ after keeping the FET in atmosphere is shown as a function of time in Figure S9(a). The μ values do not change even if the FETs are stored in atmosphere for 7 days. On the other hand, as seen from Figure S9(b), the μ values drastically decrease when heating the FETs above 100°C for 1 h, implying that the picene-(C14H29)2 thin-film deteriorates at high temperature, i.e., picene-(C14H29)2 molecule probably sublimes. As a consequence, the picene-(C14H29)2 FET is stable under atmospheric condition, while it deteriorates above 100°C.

The transfer curves of picene-(C14H29)2 thin-film FETs with HfO2 and PZT are shown in Figures 2(c) and (d), respectively; these also show p-channel FET characteristics. The μ, Vth, on-off ratio and S were 7.7 cm2 V−1 s−1, −11 V, 3.4 × 106 and 1.1 V decade−1, respectively, for a picene-(C14H29)2 thin-film FET with an HfO2 gate dielectric, becoming 13 cm2 V−1 s−1, −9.8 V, 1.6 × 106 and 9.8 × 10−1 V decade−1, respectively, for a picene-(C14H29)2 thin-film FET with a PZT gate dielectric. We made additional picene-(C14H29)2 thin-film FETs with ZrO2 and Ta2O5 gate dielectrics (Figure S6 in Supplementary information). The μ values are 7.0 cm2 V−1 s−1 for ZrO2 and 6.3 cm2 V−1 s−1 for Ta2O5. The <μ>, , , and from five picene-(C14H29)2 FETs with HfO2 gate dielectric are 5(1) cm2 V−1 s−1, −10.4(5) V, 8(15) × 105, and 1.4(2) V decade−1, respectively, while the <μ>, , , and from twelve picene-(C14H29)2 FETs with PZT gate dielectric are 14(4) cm2 V−1 s−1, −7(1) V, 2.4(7) × 106, and 0.9(1) V decade−1. The highest μ value reaches 20.9 cm2 V−1 s−1 in picene-(C14H29)2 FET with PZT gate dielectric. All FET parameters in FETs with HfO2 and PZT are shown in Table 2 and 3, respectively. Thus, the μ values are quite high in picene-(C14H29)2 thin-film FETs with high k-dielectrics. In particular, the picene-(C14H29)2 FET with PZT gate dielectric accompanies both high mobility and low-voltage operation. To our knowledge, the μ value, 20.9 cm2 V−1 s−1, recorded in this study is the highest in organic thin-film FETs at the present stage. The FET parameters recorded for picene-(C14H29)2 FET with Ta2O5 (six FETs) and ZrO2 (six FETs) gate dielectrics are shown in Table 4 and 5, respectively, together with their average values.

Table 2

FET characteristics of picene-(C14H29)2 thin film FETs with an HfO2 dielectric. W = 500 μm

sample	μ (cm2V−1s−1)	|Vth| (V)	ON/OFF	S (V/decade)	L (μm)
#1	7.7	10.92	3.4 × 106	1.08	450
#2	4.2	10.61	1.2 × 105	1.16	350
#3	4.6	10.00	1.1 × 105	1.40	450
#4	4.8	9.78	1.4 × 105	1.50	450
#5	5.6	10.84	5.1 × 103	1.68	600
average	5(1)	10.4(5)	8(15) × 105	1.4(2)

Table 3

FET characteristics of picene-(C14H29)2 thin film FETs with a PZT dielectric. W = 600 μm

sample	μ (cm2V−1s−1)	|Vth| (V)	ON/OFF	S (V/decade)	L (μm)
#1	13.1	9.8	1.6 × 106	0.98	450
#2	10.3	6.5	3.0 × 106	0.74	150
#3	12.9	6.7	3.6 × 106	0.75	150
#4	14.3	6.6	2.9 × 106	0.65	200
#5	13.0	6.6	2.5 × 106	0.71	200
#6	9.3	5.6	3.1 × 106	0.89	200
#7	13.0	6.6	2.5 × 106	0.90	200
#8	20.9	7.9	2.3 × 106	0.81	300
#9	17.9	6.5	2.0 × 106	0.84	300
#10	11.4	5.8	1.9 × 106	1.1	300
#11	15.8	6.8	2.2 × 106	1.1	300
#12	19.7	5.2	8.9 × 105	1.0	450
average	14(4)	7(1)	2.4(7) × 106	0.9(1)

Table 4

FET characteristics of picene-(C14H29)2 thin film FETs with a Ta2O5 dielectric. W = 500 μm except for sample #1, and W = 600 μm for sample #1

sample	μ (cm2V−1s−1)	|Vth| (V)	ON/OFF	S (V/decade)	L (μm)
#1	6.3	13.0	4.6 × 106	1.13	450
#2	3.3	10.9	1.6 × 105	0.710	300
#3	4.9	9.33	2.4 × 105	1.19	450
#4	6.4	9.91	2.7 × 105	1.15	450
#5	7.6	10.5	2.5 × 105	1.13	450
#6	4.6	10.0	1.6 × 105	1.04	600
average	5(2)	11(1)	9(18) × 105	1.0(2)

Table 5

FET characteristics of picene-(C14H29)2 thin film FETs with a ZrO2 dielectric. W = 500 μm

sample	μ (cm2V−1s−1)	|Vth| (V)	ON/OFF	S (V/decade)	L (μm)
#1	7.0	10.8	1.1 × 107	0.43	450
#2	8.9	7.6	1.4 × 106	0.40	135
#3	9.6	7.4	1.0 × 106	0.84	200
#4	8.6	6.1	7.0 × 105	0.89	300
#5	12.0	8.2	4.1 × 105	0.86	450
#6	10.3	8.0	6.1 × 105	1.0	300
*#7	23.3	10.8	6.7 × 105	1.1	450
average	9(2)	8(2)	3(4) × 106	0.7(3)

The output curves of picene-(C14H29)2 FETs with high k-gate dielectrics (Figure S7 in Supplementary information) show p-channel FET characteristics with clear saturation behaviour in the high |VD| regime, but a little concave behaviour in the low |VD| regime, which indicates a large contact resistance, in spite of the presence of a 3 nm thick 2,3,5,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ) layer between the source/drain electrodes and the picene-(C14H29)2 thin film. The origin of this resistance is still not clear, and a design to lower it is necessary for picene-(C14H29)2 thin-film FETs with high-k gate dielectrics.

FET characteristics of solution-processed picene-(C14H29)2 thin-film FET

Finally, we fabricated a picene-(C14H29)2 thin-film FET by depositing the film from solution, and measured its FET characteristics. An optical image of the thin film is shown in Figure 3(a), showing large grains. The XRD pattern of the thin film is shown in Figure 3(b) together with that of a powder sample, which differs from that of the thin film formed by thermal deposition (Figure 1(c)) and is similar to that of powder. This pattern implies that there is no parallel stacking of layers on SiO2 surface. Actually, as indicated from the optical image, the grains aggregate on the SiO2 surface, indicating a strong interaction between grains, as small granules precipitate from the solution.

The output and transfer curves of a solution-deposited picene-(C14H29)2 thin-film FET are shown in Figures 3(c) and (d), respectively. These show p-channel FET characteristics, and the μ, Vth, on-off ratio and S are 3.4 × 10−2 cm2 V−1 s−1, −48 V, 3.3 × 105 and 6.1 V decade−1, respectively. The μ value of a solution-deposited picene-(C14H29)2 thin-film FET observed in this study is lower by two orders of magnitude than that, 2.0 cm2 V−1 s−1, previously reported32.

Discussion

We have succeeded in fabricating a high-performance picene-(C14H29)2 thin-film FET with various gate dielectrics. Here, the characteristics observed are discussed and the strategy for a further improvement will be presented.

The <μ> value, 7(2) cm2 V−1 s−1, in a picene-(C14H29)2 thin film FET with SiO2 gate dielectric was higher than those of thin-film FETs with picene (1.0–3.0 cm2 V−1 s−1)1314 and [7]phenacene (0.8 cm2 V−1 s−1)20, while comparable to that (7.4 cm2 V−1 s−1)19 of a [6]phenacene thin-film FET. Despite the absence of parallel planes stacked on the SiO2 surface, the <μ> value is higher than that of thin-film FET with picene, suggesting a presence of other factor such as high overlap (transfer integral) between molecules in picene-(C14H29)2 thin film. Here it is important to notice that a 3 nm layer of F4TCNQ is inserted between the electrodes and the thin film. This should provide a small Schottky barrier height (or a small contact resistance) and a low |Vth| as reported previously for organic single-crystal FETs27.

The <μ> values in picene-(C14H29)2 thin film FETs with high-k gate dielectrics (5(1) cm2 V−1 s−1 for HfO2, 14(4) cm2 V−1 s−1 for PZT, 5(2) cm2 V−1 s−1 for Ta2O5 and 9(2) cm2 V−1 s−1 for ZrO2) are comparable to that, 7(2) cm2 V−1 s−1, for a picene-(C14H29)2 thin-film FET with an SiO2 gate dielectric, as seen from Tables 1,2,3,4,5. It is worth noting that the maximum μ value, 20.9 cm2 V−1 s−1, for picene-(C14H29)2 thin-film FET with PZT gate dielectric (Table 3) is the highest value yet reported for organic FETs; as seen from Table 5, the μ value as high as 23.3 cm2 V−1 s−1 is observed, but the value is not included in discussion because it is much higher than the other μ values listed in Table 5. Currently, the highest μ is 17.2 cm2 V−1 s−1 for a bis(benzothieno)naphthalene thin-film FET29. To our knowledge, even the <μ> of 14(4) cm2 V−1 s−1 for picene-(C14H29)2 thin-film FET with PZT gate dielectric is now the third-highest2930. The <|Vth|> does not exceed 11 V for high-k gate dielectrics. The FET performance achieved using picene-(C14H29)2 thin film and high-k gate dielectrics in this study is excellent and satisfactory, but study on the reason why the picene-(C14H29)2 thin film provides such FET characteristics should be made, in particular crystal structure analysis is indispensable. Through the work, we must improve the performance rapidly.

The μ value of our solution-processed FET was lower than that for the previous report32. Although the details of the device structure and the formation of the thin film are not clear for the high-performance solution-deposited FET with reported picene-(C14H29)2 in ref. 32, the formation of a homogeneous thin film may be a key to higher μ values, because the obtained thin film by deposition from solution is powder-like, i.e., the growth of an ab-plane parallel to the SiO2 surface is not still achieved.

In conclusion, the FET with a PZT gate dielectric achieved a <μ> as high as 14(4) cm2 V−1 s−1, and the was −7(1) V. This <μ> is now the third-highest so far reported for an organic FET, and the highest in FETs based on thin films of pure hydrocarbon molecules. Furthermore, we observed the high μ values greater than 3 cm2 V−1 s−1 in all picene-(C14H29)2 FETs (see Tables 1,2,3,4,5), especially the maximum μ reaches ~21 cm2 V−1 s−1 with PZT dielectric. Low-voltage operation (<|Vth|> ≤ ~11 V) was achieved with high-k gate dielectrics, implying excellent FET performance of picene-(C14H29)2 thin film FETs with high k-gate dielectrics and an importance of combination of picene-(C14H29)2 and high-k gate dielectrics.

This molecule contains long alkyl chains, which may produce a strong interaction between molecules. This seems to lead to the aggregation of granules in thin films prepared from solution, i.e., precipitation is easily produced. Nevertheless, the solution-deposited thin-film FET using this precipitate easily provided p-channel FET characteristics with a μ as high as 3.4 × 10−2 cm2 V−1 s−1. These results show the promise of using an alkyl-substituted picene in the search for a practical high-performance transistor. The observation of the high <μ> ( = 14(4) cm2 V−1 s−1) in the FET must open an avenue for ubiquitous electronics based on picene derivatives.

Methods

Picene-(C14H29) was synthesized using the following reaction steps (see Figure 4). (1) 6-Bromo-1-(bromomethyl)naphthalene 1 was converted to the phosphonium salt 2 by substitution with triphenylphosphine. (2) It was then converted to naphthaldehyde 3 by the Sommelet reaction33. (3) A Wittig reaction between compounds 2 and 3 produced dinaphthylethene 4. (E)- and (Z)-isomers of compound 4 were obtained in 52% and 46% yields, respectively. It is known that (E)-diarylethenes can be used for stilbene-like photocyclization, because E-to-Z isomerization occurs under the photoreaction conditions343536. (4) Both (E)- and (Z)-4 were used as the precursor to dibromopicene 5; a special flow reactor37 was used for this reaction. Photocyclization of (E)- and (Z)-4 effectively proceeded to afford dibromopicene 5 in 89% and 91% yields, respectively. (5) The tetradecyl chains were introduced by the Kumada-Tamao cross-coupling reaction38 in the presence of a Pd catalyst in 75% yield. The synthesis and experimental details relevant to picene-(C14H29)2 in ref. 32 differ from those in this study. The merits of our synthesis are fully described in Supplementary information.

Figure 4

Synthetic route to picene-(C14H29)2.

(a) PPh3, toluene, reflux 18 h, 95%; (b) hexamethylenetetramine, CHCl3, reflux, 1 h, then heat in AcOH-H2O for 1.5 h, 72%; (c) KOH, CH2Cl2-H2O, r.t., 17 h,(E)-4 52%, (Z)-4 46%; (d) hν (flow reactor)37, I2, O2, toluene, irradiation time 15 min, 89%. (e) C14H29MgBr, PdCl2(dppf)-CH2Cl2, 75%.

Picene-(C14H29) was characterized by NMR spectroscopy (Figure S5 in Supplementary information) and elemental analysis. In the 1H NMR spectrum, three downfield-shifted signals assignable to the protons located in the bay region of the picene framework were observed: 8.89 ppm (s, H(13,14)), 8.74 ppm (d, J = 9.1 Hz, H(1,11)) and 8.73 ppm (d, J = 8.5 Hz, H(6,7)). The signals of protons at the edges of the picene core appeared in the higher field: 7.76 ppm (bs, H(4,9)), 7.56 ppm (dd, J = 8.5, 1.8 Hz, H(2,12)). These observations are consistent with the1H NMR spectral features of previously reported extended phenacene343536, and provide evidence for the presence of pure picene-(C14H29)2.

The FET devices using a thin film of picene-(C14H29)2 were fabricated on various gate dielectrics such as SiO2, Ta2O5, ZrO2, HfO2 and PZT. The SiO2 layer was made by thermal oxidation of Si, and we used a commercially available SiO2/Si substrate. The other gate dielectrics were synthesized by magnetron RF sputtering for Pt(50 nm)/Si substrate. The layers of SiO2, Ta2O5, ZrO2, HfO2 and PZT were 400, 50, 53, 50 and 150 nm thick, respectively. The surface of gate dielectrics other than SiO2 was coated with 50 nm thick parylene, while the surface of SiO2 was coated with hexamethyldisilazane (HMDS); the coating methods for parylene and HMDS are described in ref. 39 and Supplementary information, respectively. The capacitance per area, Co, of SiO2, Ta2O5, ZrO2, HfO2 and PZT were experimentally determined to be 8.3, 54, 35, 35 and 36 nF cm−2, respectively, by LCR meter; all Co was estimated by extrapolation of the capacitance measured at 20 Hz–1 kHz to 0 Hz, i.e., the Co at 0 Hz. The plots of C0 – frequency (f) for all gate dielectrics are shown in Figure S8 in Supplementary information. Therefore, the Co is not underestimated, leading to the exact μ value.

The thin film of picene-(C14H29)2 was formed by either thermal deposition at 10−7 Torr or deposition from a CHCl3 solution. The thin film prepared by thermal deposition was 60 nm thick, while the thickness of the solution-deposited film was more than 1 μm. Details of the solution-deposition process are described in Supplementary information. The source and drain electrodes were formed with gold (Au) by thermal deposition at 10−7 Torr. The thickness of Au electrodes was 50 nm. 3 nm thick F4TCNQ was inserted into the space between electrodes and thin film. The channel length, L, and width, W, of the FET device are specified in figure captions and tables. The device structure (top-contact type) is shown in Figure 1(b). The FET characteristics were recorded in two-terminal measurement mode using a semiconductor parametric analyzer (Agilent B1500A) in an Ar-filled glove box; in measurement of FET characteristics, the source voltage, VS, is grounded (source-grounded), or VS = 0 V. All FET parameters are evaluated from the square root of absolute forward transfer curve (|ID|1/2 – VG) because of a saturation regime; the |ID|1/2 – VG curves are shown for all transfer curves in this paper.

To check the statistical reproducibility of FET characteristics, the FET characteristics of picene-(C14H29)2 thin film FETs with various dielectrics are summarized in Tables 1,2,3,4,5. The average values and the standard deviations of FET parameters are shown in the bottom row. The transfer and output curves of sample #1 in each table (see Tables 1,2,3,4,5) are shown in this paper, and the FET characteristics are described in the main text. The sample indicated by an asterisk in Table 5 is not used for average, because it shows much higher mobility than those for the other samples in Table 5. The channel width is 500 μm for the devices with SiO2, HfO2, Ta2O5, and ZrO2 dielectrics, and 600 μm for the devices with a PZT dielectric.

The XRD and AFM were measured using Smart Lab-Pro (RIGAKU) and an SPA 400-DFM (SII Nano Technologies), respectively. The X-ray wavelength was 1.5418 Å (Cu Kα source).

Author Contributions

H.O., Y.K. and R.E. designed this research project and supervised experiments. H.O. and S.G. performed synthesis and characterization of picene-(C14H29)2 sample. S.H., R.E. and H.G. carried out FET works and characterization of thin films. Y.S. and M.I. performed works of XRD and AFM. H.O. and R.E. wrote the parts of synthesis and FET work of this paper, respectively, and YK combined them and modified to complete the paper. S.H., H.G. and Y.K. carried out the additional experiments and analyses on the durability and reproducibility of FET performance. R.E. managed (edited) all parts of this paper under the discussion with Y.K.