Improvement of optical transmittance and electrical properties for the Si quantum dot-embedded ZnO thin film.

A Si quantum dot (QD)-embedded ZnO thin film is successfully fabricated on a p-type Si substrate using a ZnO/Si multilayer structure. Its optical transmittance is largely improved when increasing the annealing temperature, owing to the phase transformation from amorphous to nanocrystalline Si QDs embedded in the ZnO matrix. The sample annealed at 700°C exhibits not only high optical transmittance in the long-wavelength range but also better electrical properties including low resistivity, small turn-on voltage, and high rectification ratio. By using ZnO as the QDs' matrix, the carrier transport is dominated by the multistep tunneling mechanism, the same as in a n-ZnO/p-Si heterojunction diode, which clearly differs from that using the traditional matrix materials. Hence, the carriers transport mainly in the ZnO matrix, not through the Si QDs. The unusual transport mechanism using ZnO as matrix promises the great potential for optoelectronic devices integrating Si QDs.

Background

Recently, Si quantum dots (QDs) embedded in traditionn>an class="Chemical">al Si-based dielectric matrix materials like SiO2 and Si3N4 have been extensively studied and successfully applied to various optoelectronic devices [1-3], owing to their many unique characteristics such as highly tunable bandgap and better optical properties [4-6]. In particular, Si QD is persistently considered as a candidate for next-generation light emitters in Si photonics because of its greatly improved internal and external quantum efficiencies [7,8]. To further improve the device performance, utilization of Si-rich Si-based dielectric materials as Si QDs’ matrices has also been developed [9,10]. A suitable matrix material for Si QDs is very important for better device performance. We propose to embed Si QDs into a ZnO thin film because ZnO has many desirable features to function as Si QDs’ matrix material, e.g., wide and direct bandgap, high transparency, and highly tunable electrical properties [11]. Hence, ZnO can serve as the Si QDs’ matrix to achieve bandgap engineering, reduce the optical loss from the matrix’s absorption, and efficiently enhance the carrier transport efficiency for optoelectronic device application. The fabrication and fundamental optical properties of the Si QD-embedded ZnO thin films have been reported in our previous works [12,13]. In this study, improvement of optical transmittance and electrical properties of the Si QD-embedded ZnO thin films is investigated and discussed.

Methods

The ZnO/n>an class="Chemical">Si multilayer (ML) thin films with 20 bilayers are deposited on p-type Si (100) substrates or fused quartzes at room temperature using the radio-frequency (RF) magnetron sputtering method. The sputtering powers of ZnO and Si are fixed at 75 and 110 W, and the effective thicknesses of each ZnO and Si layer are fixed at 5 and 3 nm, respectively. After deposition, the ZnO/Si ML thin films are annealed at 500°C, 600°C, 700°C, or 800°C for 30 min in N2 environment. For electrical measurements, 100-nm-thick Al and Ni metal layers are deposited on the top and bottom surfaces of devices as electrodes using a thermal coater. The Raman spectra are measured using a 488-nm diode-pumped solid-state laser (HORIBA LabRam HR, HORIBA, Kyoto, Japan). The X-ray diffraction (XRD) patterns are examined by a Bede-D1 X-ray diffractometer with Cu Kα radiation (Bede Scientific, Engelwood, CO, USA). The transmittance spectra are obtained using a UV–vis-NIR spectrophotometer (Hitachi U-4100, Hitachi Ltd., Chiyoda, Tokyo, Japan). The cross-sectional morphologies are observed by a JSM-6500 F field-emission scanning electron microscope (SEM; JEOL Ltd., Akishima, Tokyo, Japan). The current–voltage (I-V) curves are measured using an Agilent E5270B precision measurement mainframe (Agilent Technologies Inc., Santa Clara, CA, USA).

Results and discussion

In our previous works, we demonstrated that a high Si spn>uttering power can assist the formation of the self-aggregated amorphous Si QDs embedded in the ZnO matrix during deposition by utilizing a ZnO/Si ML structure [12]. In order to investigate the crystalline properties of the Si QDs embedded in ZnO thin films under different annealing temperatures (Tann) for a longer annealing duration, Raman spectra are measured and shown in Figure 1. Generally, the signal of Si materials can be decomposed into three components including the peaks located at approximately 480, 500 ~ 510, and 510 ~ 520 cm-1, which originated from the transverse optical (TO) modes of Si-Si vibrations in the amorphous (a-Si), intermediate (i-Si), and nanocrystalline Si (nc-Si) phases [14]. The corresponding crystalline volume fractions of Si (fc) obtained from fitting the curves are shown in the inset of Figure 1[14]. The nc-Si phase is formed in the ZnO matrix and significantly increased by increasing Tann when Tann is higher than 600°C. This indicates that a higher Tann can largely enhance the crystalline quality of Si QDs embedded in the ZnO matrix.

Figure 1

Crystalline properties of Si QDs. Raman spectra of the Si QD-embedded ZnO thin films under different Tann. The inset shows the corresponding crystalline volume fractions of Si (fc).

Crystalline propn>erties of n>an class="Chemical">Si QDs. Raman spectra of the Si QD-embedded ZnO thin films under different Tann. The inset shows the corresponding crystalline volume fractions of Si (fc).

Since the crystalline properties of the ZnO matrix can influence its optical and electrical properties [15], the XRD patterns of the Si QD-embedded ZnO thin films annealed at different temperatures are examined and shown in Figure 2a, fine-scanned from 30° to 40°. A main diffraction signal is observed at approximately 34.5° for all the samples. As shown in Figure 2b and its inset, this signal can be decomposed into two components in Gaussian form with peaks located at about 34.3° and about 36.3°, which are contributed from (002) and (101) orientations of ZnO [16]. In Figure 2a, the crystallization intensity of the ZnO matrix is slightly reduced when increasing Tann. This may be due to the increased interior film stress resulting from the phase transformation of a- to nc-Si QDs. From the results of Raman and XRD measurements, we show that the nc-Si QDs embedded in the crystalline ZnO matrix can be achieved by a Tann higher than 600°C.

Figure 2

Crystalline properties of ZnO matrix. (a) XRD patterns fine-scanned from 30° to 40° of the Si QD-embedded ZnO thin films under different Tann. (b) Full XRD pattern of the Si QD-embedded ZnO thin film annealed at 700°C. The inset shows the curve fitting result for the main diffraction signal.

Crystalline propn>erties of n>an class="Chemical">ZnO matrix. (a) XRD patterns fine-scanned from 30° to 40° of the Si QD-embedded ZnO thin films under different Tann. (b) Full XRD pattern of the Si QD-embedded ZnO thin film annealed at 700°C. The inset shows the curve fitting result for the main diffraction signal.

The optical transmittance spn>ectra of the n>an class="Chemical">Si QD-embedded ZnO thin films under different Tann are shown in Figure 3. The transmittance in the long-wavelength (long-λ) range (>600 nm) clearly increases when increasing Tann. Since higher Tann can obviously enhance the crystallization of Si QDs, the improved optical transmittance in the long-λ range can be attributed to the decreased absorbance from a-Si QDs due to the increased fc of Si QDs [5]. It is worthy to note that high transmittance of approximately 90% in the long-λ range under a Tann higher than 700°C can be achieved and is close to those using the traditional matrix materials [5]. From the above results, it is clear that better crystallization of Si QDs in the ZnO matrix is required to decrease the absorption from a-Si QDs and thus efficiently reduce the optical loss in the long-λ range for better optoelectronic device performance. We find that a high-enough Tann for the Si QD-embedded ZnO thin film is critical to significantly improve the optical properties.

Figure 3

Optical properties. Optical transmittance spectra of the Si QD-embedded ZnO thin films under different Tann.

Optical propn>erties. Opn>ticn>an class="Chemical">al transmittance spectra of the Si QD-embedded ZnO thin films under different Tann.

The images of the Si QD-embedded n>an class="Chemical">ZnO thin films after annealing are examined by SEM. The local film prominences are observed when Tann is higher than 600°C. Figure 4a shows the cross-sectional SEM image of a sample annealed at 700°C. The local film prominence density and diameter in average are estimated and shown in Figure 4b. The prominence density increases almost linearly from 5.5 to 7.6 ones per 10 × 10 μm2 when increasing Tann from 600°C to 800°C with a close average diameter of about 2 μm. According to Raman spectra, the phase transformation of a- to nc-Si QDs happens when Tann is larger than 600°C, and fc also increases with increasing Tann from 600°C to 800°C. This strong correlation between fc and prominence density means that the volume variation from the phase transformation of a- to nc-Si QDs embedded in the ZnO matrix during annealing can produce an interior film stress and lead to the occurrence of local film prominences.

Figure 4

Thin film image. (a) Cross-sectional SEM image and (b) local film prominence density and diameter in average for the Si QD-embedded ZnO thin films after annealing.

Thin film image. (a) Cross-sectional SEM image and (b) locn>an class="Chemical">al film prominence density and diameter in average for the Si QD-embedded ZnO thin films after annealing.

To understand the electrical propn>erties of the n>an class="Chemical">Si QD-embedded ZnO thin films, the vertical resistivity (ρ) is calculated from the slope of the I-V curve under a high forward bias region of 4 ~ 5 V. When increasing Tann, the ρ can be reduced by the improved crystalline quality of Si QDs but also raised by the increased film prominence density and degraded crystalline quality of the ZnO matrix. Figure 5a shows the obtained ρ under different Tann, which slightly increases when increasing Tann from 500°C to 700°C but still keeps a low resistivity of approximately 104 Ω cm, significantly lower than that (approximately 108 Ω cm) of the intrinsic Si QDs embedded in a SiO2 matrix [17,18]. It is evident that using ZnO as matrix can overcome the issue of highly resistive nature of the traditional Si-based dielectric matrix materials, and 104 times improvement of ρ is obtained. The ρ largely increases for the sample annealed at 800°C, which may have resulted from the excess film prominences produced during annealing since the film prominences will lead to local broken circuit regions at the interface of film/substrate and significantly increase the resistivity. Hence, we can conclude that annealing at 700°C is a more suitable annealing condition to have better crystallization of Si QDs in the crystalline ZnO matrix, low ρ, and high transmittance in the long-λ range. The logarithmic I-V curve of the sample annealed at 700°C is shown in Figure 5b, and its inset shows the corresponding linear I-V curve in magnification. It clearly exhibits not only a good rectification ratio of 3.4 × 103 at ±5 V but also a low turn-on voltage (Vt) of 0.48 V, which agrees with the reported results of the n-ZnO/p-Si heterojunction (HJ) diode [19,20]. Even though the Si QDs are embedded in the ZnO matrix, we show that the fabricated ZnO thin film on p-Si can still possess good p-n HJ diode behavior with large rectification ratio and low Vt.

Figure 5

Electrical properties. (a) Vertical resistivity of the Si QD-embedded ZnO thin films under different Tann. (b) Logarithmic I-V curve of the sample annealed at 700°C. The inset shows the linear I-V curve in magnification.

Electrical propn>erties. (a) Verticn>an class="Chemical">al resistivity of the Si QD-embedded ZnO thin films under different Tann. (b) Logarithmic I-V curve of the sample annealed at 700°C. The inset shows the linear I-V curve in magnification.

To investigate the carrier transport mechanism, the temperature-dependent forward I-V curves of the sample annealed at 700°C are examined and shown in Figure 6a. The I-V curves exhibit the typn>icn>an class="Chemical">al temperature dependence of a p-n junction diode. The current clearly increases as we raise the measurement temperature (Tmeas). In the low bias region (smaller than approximately 0.5 V), the currents can be well fitted to be proportional to about V1.2 for different Tmeas, which slightly deviates from the ohmic behavior. This means that the surface states and/or an inherent insulating SiO2 thin layer at the interface of the n-ZnO matrix/p-Si substrate has influence on the transport of carriers [21]. In the high bias region (larger than approximately 0.5 V), the forward currents can be well expressed by I = Is[exp(BV) - 1] for different Tmeas, where Is is the reverse saturation current and parameter B is a coefficient dependent or independent on temperature decided by the dominant carrier transport mechanism [21,22]. The fitted results for parameter B are shown in Figure 6b, which reveal that the parameter B is almost invariant for different Tmeas. This independence of Tmeas indicates that the carrier transport is dominated by the multistep tunneling mechanism, which had been reported by Zebbar et al. and Dhananjay et al. for the n-ZnO/p-Si HJ diode [21,23]. The multistep tunneling process usually occurs at the HJ region of the n-ZnO matrix and p-Si substrate, which is attributed to the recombination of electrons, tunneling from ZnO into the empty gap states in the p-Si substrate, and holes, tunneling through the HJ barrier from the p-Si substrate to the n-ZnO matrix between the empty states [21,23]. Hence, our results show that the carriers in the Si QD-embedded ZnO thin film mainly transport via the ZnO matrix but not through Si QDs with direct, resonant, or phonon-assisted tunneling mechanisms, as reported for Si QDs embedded in the traditional matrix materials [24,25]. According to the multistep tunneling mechanism, the temperature dependence of Is is given by the relation, Is ∝ exp(-Ea/kT), where Ea is the activation energy, k is Boltzmann’s constant, and T is the absolute temperature [21,23]. Figure 6c shows the Arrhenius plot of ln(Is) versus 1,000/T. A linear relationship is clearly observed, which further confirms that the dominating carrier transport process is the multistep tunneling mechanism [19,21-23]. The Ea of around 0.37 eV obtained from the Arrhenius plot is a little larger than those of the reported n-ZnO/p-Si HJ diodes, which are usually smaller than 0.3 eV [19,21-23]. This means that the thermally activated carriers are partially contributed from the embedded Si QDs since the intrinsic Si QDs can possess Ea larger than 0.4 eV [17,26]. Thus, we can conclude that the Si QDs embedded in ZnO matrix also contribute the carriers, and those carriers will partially escape from Si QDs into the ZnO matrix and transport inside. The largely improved resistivity suggests that the carriers transporting in the ZnO matrix can have a much better transport efficiency than those tunneling through barriers in the traditional matrix materials. With the unique carrier transport mechanism and better electrical properties, we believe that the Si QD thin films will have great potential for optoelectronic device application by using ZnO as matrix material.

Figure 6

Carrier transport mechanism. (a) Forward I-V curves for different measurement temperatures, (b) the parameter B, and (c) Arrhenius plot of ln(Is) versus 1,000/T for the Si QD-embedded ZnO thin film annealed at 700°C.

Carrier transport mechanism. (a) Forward I-V curves for different measurement temperatures, (b) the parameter B, and (c) Arrhenius plot of ln(Is) versus 1,000/T for the pan class="Chemical">Si QD-embedded n>an class="Chemical">ZnO thin film annealed at 700°C.

Conclusions

In summary, we successfully fabricate a nc-Si QD-embedded n>an class="Chemical">ZnO thin film on a p-Si substrate using a ZnO/Si ML deposition structure. Our results indicate that the optical transmittance can be largely enhanced by increasing Tann owing to the phase transformation of a- to nc-Si QDs embedded in the ZnO matrix, and up to about 90% transmittance in the long-λ range under a Tann higher than 700°C is obtained. The Si QD-embedded ZnO thin film annealed at 700°C exhibits good diode behavior with a large rectification ratio of approximately 103 at ±5 V and significantly lower resistivity than that using the SiO2 matrix material (104 times improvement). From temperature-dependent I-V curves, we find that the carriers transport mainly via the ZnO matrix, not through Si QDs, which is dominated by the multistep tunneling mechanism as in the n-ZnO/p-Si HJ diode. The unique transport mechanism differing from those using the traditional Si-based dielectric matrix materials can lead to much better carrier transport efficiency and electrical properties. Hence, we show that the Si QD thin film using the ZnO matrix material is very advantageous and has potential for optoelectronics device application.

Competing interests

The authors declare that they have no competing interests.

Authors’ contributions

KYK and PTL carried out the expn>erimentn>an class="Chemical">al design and analysis and drafted the manuscript. CCL carried out the experimental fabrication and measurements. PRH, SWH, WLC, and YJC participated in the experimental fabrication. All authors read and approved the final manuscript.