OBJECTIVES: To evaluate the effect of composite resins (one conventional and two low-shrink composites) and filling techniques on cuspal strains (CS), microtensile bond strength (μTBS), composite ultimate tensile strength (UTS), and mechanical properties of the composites at various depths in molars with large Class II restorations. MATERIALS AND METHODS: One hundred seventeen human molars received standardized Class II mesio-oclusal-distal cavity preparations and restorations with three composites (Filtek LS [3M-ESPE]; Aelite LS [BISCO]; and Filtek Supreme [3M-ESPE]) using three filling techniques (bulk, eight increments, and 16 increments). CS was measured using strain gauges, after which the same restored teeth were used to assess μTBS and UTS. The elastic modulus (E) and Vickers hardness (VH) at different depths were determined from microhardness indentations. The CS, μTBS, UTS, E, and VH data were statistically analyzed using split-plot analysis of variance and Tukey test (p=0.05). RESULTS: The CS was higher when using 16 increments. The 'low-shrink' composites caused lower CS. The μTBS and UTS were similar for eight- and 16-increment techniques and higher when compared to the bulk filling in all composites. E and VH were constant through the depth when applied in eight or 16 increments. CONCLUSIONS: Type of composite and filling technique affected the CS, μTBS, UTS, and mechanical properties of large Class II restorations. The eight-increments filling technique resulted in generally less CS with the same μTBS and UTS than was obtained with 16 increments, without affecting E and VH through the depth of the composites.
OBJECTIVES: To evaluate the effect of composite resins (one conventional and two low-shrink composites) and filling techniques on cuspal strains (CS), microtensile bond strength (μTBS), composite ultimate tensile strength (UTS), and mechanical properties of the composites at various depths in molars with large Class II restorations. MATERIALS AND METHODS: One hundred seventeen human molars received standardized Class II mesio-oclusal-distal cavity preparations and restorations with three composites (Filtek LS [3M-ESPE]; Aelite LS [BISCO]; and Filtek Supreme [3M-ESPE]) using three filling techniques (bulk, eight increments, and 16 increments). CS was measured using strain gauges, after which the same restored teeth were used to assess μTBS and UTS. The elastic modulus (E) and Vickers hardness (VH) at different depths were determined from microhardness indentations. The CS, μTBS, UTS, E, and VH data were statistically analyzed using split-plot analysis of variance and Tukey test (p=0.05). RESULTS: The CS was higher when using 16 increments. The 'low-shrink' composites caused lower CS. The μTBS and UTS were similar for eight- and 16-increment techniques and higher when compared to the bulk filling in all composites. E and VH were constant through the depth when applied in eight or 16 increments. CONCLUSIONS: Type of composite and filling technique affected the CS, μTBS, UTS, and mechanical properties of large Class II restorations. The eight-increments filling technique resulted in generally less CS with the same μTBS and UTS than was obtained with 16 increments, without affecting E and VH through the depth of the composites.
Authors: Vilhelm G Ólafsson; André V Ritter; Edward J Swift; Lee W Boushell; Ching-Chang Ko; Gabrielle R Jackson; Sumitha N Ahmed; Terence E Donovan Journal: J Esthet Restor Dent Date: 2017-10-16 Impact factor: 2.843
Authors: Atais Bacchi; Victor Pinheiro Feitosa; Andrea Soares Quirino da Silva Fonseca; Larissa Maria Assad Cavalcante; Nikolaos Silikas; Luis Felipe Jochins Schneider Journal: J Conserv Dent Date: 2015 Sep-Oct
Authors: Ana Luíza Serralha de Velloso Vianna; Célio Jesus do Prado; Aline Aredes Bicalho; Renata Afonso da Silva Pereira; Flávio Domingues das Neves; Carlos José Soares Journal: J Appl Oral Sci Date: 2018-08-20 Impact factor: 2.698