Literature DB >> 22995403

Biodegradable nanocomposite hydrogel structures with enhanced mechanical properties prepared by photo-crosslinking solutions of poly(trimethylene carbonate)-poly(ethylene glycol)-poly(trimethylene carbonate) macromonomers and nanoclay particles.

Shahriar Sharifi1, Sebastien B G Blanquer, Theo G van Kooten, Dirk W Grijpma.   

Abstract

Soft hydrogels with elasticity modulus values lower than 100kPa that are tough and biodegradable are of great interest in medicine and in tissue engineering applications. We have developed a series of soft hydrogel structures from different methacrylate-functionalized triblock copolymers of poly(ethylene glycol) (PEG) with poly(trimethylene carbonate) (PTMC) by photo-crosslinking aqueous solutions of the macromonomers in 2.5 and 5wt.% colloidal dispersions of clay nanoparticles (Laponite XLG). The length of the PTMC blocks of the macromonomers and the clay content determined the physicomechanical properties of the obtained hydrogels. While an increase in the PTMC block length in the macromonomers from 0.2 to 5kg/mol resulted in a decrease in the gel content, the addition of 5wt.% Laponite nanoclay to the crosslinking solution lead to very high gel contents of the hydrogels of more than 95%. The effect of PTMC block length on the mechanical properties of the hydrogels was not as pronounced, and soft gels with a compressive modulus of less than 15kPa and toughness values of 25kJm(-3) were obtained. However, the addition of 5wt.% Laponite nanoclay to the formulations considerably increased the compressive modulus and resilience of the hydrogels; swollen nanocomposite networks with compressive modulus and toughness values of up to 67kPa and 200kJm(-3), respectively, could then be obtained. The prepared hydrogels were shown to be enzymatically degradable by cholesterol esterase and by the action of macrophages. With an increase in PTMC block length in the hydrogels, the rates of mass loss increased, while the incorporated Laponite nanoclay suppressed degradation. Nanocomposite hydrogel structures with a designed gyroid pore network architecture were prepared by stereolithography. Furthermore, in the swollen state the porous gyroid structures were mechanically stable and the pore network remained fully open and interconnected.
Copyright © 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Entities:  

Mesh:

Substances:

Year:  2012        PMID: 22995403     DOI: 10.1016/j.actbio.2012.09.014

Source DB:  PubMed          Journal:  Acta Biomater        ISSN: 1742-7061            Impact factor:   8.947


  6 in total

1.  Electrically Driven Microengineered Bioinspired Soft Robots.

Authors:  Su Ryon Shin; Bianca Migliori; Beatrice Miccoli; Yi-Chen Li; Pooria Mostafalu; Jungmok Seo; Serena Mandla; Alessandro Enrico; Silvia Antona; Ram Sabarish; Ting Zheng; Lorenzo Pirrami; Kaizhen Zhang; Yu Shrike Zhang; Kai-Tak Wan; Danilo Demarchi; Mehmet R Dokmeci; Ali Khademhosseini
Journal:  Adv Mater       Date:  2018-01-11       Impact factor: 30.849

2.  Renaissance of Aliphatic Polycarbonates: New Techniques and Biomedical Applications.

Authors:  Jianwen Xu; Ellva Feng; Jie Song
Journal:  J Appl Polym Sci       Date:  2014-03-05       Impact factor: 3.125

3.  Insight into the Alcohol-Free Ring-Opening Polymerization of TMC Catalyzed by TBD.

Authors:  Fabrice Azemar; Olinda Gimello; Julien Pinaud; Jean-Jacques Robin; Sophie Monge
Journal:  Polymers (Basel)       Date:  2021-05-14       Impact factor: 4.329

4.  Poly(lactide-co-trimethylene carbonate) and polylactide/polytrimethylene carbonate blown films.

Authors:  Hongli Li; Jiangping Chang; Yuyue Qin; Yan Wu; Minglong Yuan; Yingjie Zhang
Journal:  Int J Mol Sci       Date:  2014-02-14       Impact factor: 5.923

5.  Bioresorbable hydrogels prepared by photo-initiated crosslinking of diacrylated PTMC-PEG-PTMC triblock copolymers as potential carrier of antitumor drugs.

Authors:  Yuandou Wang; Laishun Xi; Baogang Zhang; Qingzhen Zhu; Feng Su; Katarzyna Jelonek; Arkadiusz Orchel; Janusz Kasperczyk; Suming Li
Journal:  Saudi Pharm J       Date:  2020-01-31       Impact factor: 4.330

Review 6.  Printability and Shape Fidelity of Bioinks in 3D Bioprinting.

Authors:  Andrea Schwab; Riccardo Levato; Matteo D'Este; Susanna Piluso; David Eglin; Jos Malda
Journal:  Chem Rev       Date:  2020-08-28       Impact factor: 60.622

  6 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.