AIM: To analyse the physicochemical properties of a Nano white mineral trioxide aggregate (NWMTA) and compare it with white mineral trioxide aggregate (WMTA). METHODOLOGY: White mineral trioxide aggregate and NWMTA were prepared and mixed according to the manufacturer's instructions. Surface area of powder before hydration, setting time, X-ray diffraction and microhardness at pH values of 4.4 and 7.4 were evaluated by Brunauer-Emmett-Teller, ISO Specification no.6876, Vickers microhardness, and energy-dispersive X-ray spectroscopy equipped with X-ray colour (dot) map for both cements. anova and Mann-Whitney were used for statistical analysis at a significance level of 0.5. RESULTS: The mean ± SD of surface area and setting time were 1.8 ± 0.2 m(2) g(-1) and 43 ± 2 min for WMTA and 7.8 ± 1.2 m(2) g(-1) and 6 ± 1 min for NWMTA, respectively. Mean ± SD of Microhardness were 16 ± 2, 51 ± 1, 69 ± 1 and 81 ± 2 for WMTA at pH values of 4.4 and 7.4 and for NWMTA correspondingly. Numbers of open porosity over the surface were 88 ± 24 and 44 ± 13 for WMTA and NWMTA, respectively. Statistical tests revealed significant differences between the groups (P < 0.001) in surface area, setting time and surface hardness for both cements. Uniform distribution of strontium was only observed in NWMTA. However, other compounds were not significantly different. CONCLUSION: Increasing surface area of powder can reduce setting time and increase microhardness even at lower pH values after hydration.
AIM: To analyse the physicochemical properties of a Nano white mineral trioxide aggregate (NWMTA) and compare it with white mineral trioxide aggregate (WMTA). METHODOLOGY: White mineral trioxide aggregate and NWMTA were prepared and mixed according to the manufacturer's instructions. Surface area of powder before hydration, setting time, X-ray diffraction and microhardness at pH values of 4.4 and 7.4 were evaluated by Brunauer-Emmett-Teller, ISO Specification no.6876, Vickers microhardness, and energy-dispersive X-ray spectroscopy equipped with X-ray colour (dot) map for both cements. anova and Mann-Whitney were used for statistical analysis at a significance level of 0.5. RESULTS: The mean ± SD of surface area and setting time were 1.8 ± 0.2 m(2) g(-1) and 43 ± 2 min for WMTA and 7.8 ± 1.2 m(2) g(-1) and 6 ± 1 min for NWMTA, respectively. Mean ± SD of Microhardness were 16 ± 2, 51 ± 1, 69 ± 1 and 81 ± 2 for WMTA at pH values of 4.4 and 7.4 and for NWMTA correspondingly. Numbers of open porosity over the surface were 88 ± 24 and 44 ± 13 for WMTA and NWMTA, respectively. Statistical tests revealed significant differences between the groups (P < 0.001) in surface area, setting time and surface hardness for both cements. Uniform distribution of strontium was only observed in NWMTA. However, other compounds were not significantly different. CONCLUSION: Increasing surface area of powder can reduce setting time and increase microhardness even at lower pH values after hydration.
Authors: Mohammad Ali Saghiri; Jafar Orangi; Armen Asatourian; James L Gutmann; Franklin Garcia-Godoy; Mehrdad Lotfi; Nader Sheibani Journal: Dent Mater J Date: 2016-10-22 Impact factor: 2.102
Authors: Mohammad Ali Saghiri; Armen Asatourian; Franklin Garcia-Godoy; James L Gutmann; Nader Sheibani Journal: Biomed Res Int Date: 2013-08-24 Impact factor: 3.411