BACKGROUND: Lapidus (first metatarsocuneiform joint) arthrodesis is an established procedure for the management of hallux valgus. This study investigated the utility of fixation with a medial locking plate with adjunct compression screw versus fixation with two crossed screws. MATERIALS AND METHODS: Eight pairs of fresh-frozen human specimens were used in a matched pair test. Bone mineral density (BMD) was measured with peripheral quantitative computed tomography (pQCT). Fixation with two 4-mm-diameter crossed screws was compared versus a medial locking plate (X-Locking Plate 2.4/2.7; Synthes, Solothurn, Switzerland) with adjunct 4-mm-diameter compression screw. The specimens were tested in a four-point bending test. Parameters obtained were initial stiffness; plantar joint-line gapping after one cycle, 100 and 1000 cycles; and number of cycles to failure. Failure was defined as more than or equal to 3 mm plantar gapping. RESULTS: The groups did not differ significantly with regard to BMD (p = 0.866) and initial stiffness (p = 0.889). The plate-and-screw construct showed significantly less movement during testing, and significantly (p = 0.001) more cycles to failure than did the crossed-screw construct. There was a significant correlation (crossed-screw construct: p = 0.014; plate-and-screw construct: p = 0.010) between BMD and the number of cycles to failure. CONCLUSION: Under cyclic loading conditions, the construct using a medial locking plate with adjunct compression screw was superior to the construct using two crossed screws. CLINICAL RELEVANCE: The medial locking-plate technique described could help shorten the period of nonweightbearing and reduce the risk of non-union.
BACKGROUND: Lapidus (first metatarsocuneiform joint) arthrodesis is an established procedure for the management of hallux valgus. This study investigated the utility of fixation with a medial locking plate with adjunct compression screw versus fixation with two crossed screws. MATERIALS AND METHODS: Eight pairs of fresh-frozen human specimens were used in a matched pair test. Bone mineral density (BMD) was measured with peripheral quantitative computed tomography (pQCT). Fixation with two 4-mm-diameter crossed screws was compared versus a medial locking plate (X-Locking Plate 2.4/2.7; Synthes, Solothurn, Switzerland) with adjunct 4-mm-diameter compression screw. The specimens were tested in a four-point bending test. Parameters obtained were initial stiffness; plantar joint-line gapping after one cycle, 100 and 1000 cycles; and number of cycles to failure. Failure was defined as more than or equal to 3 mm plantar gapping. RESULTS: The groups did not differ significantly with regard to BMD (p = 0.866) and initial stiffness (p = 0.889). The plate-and-screw construct showed significantly less movement during testing, and significantly (p = 0.001) more cycles to failure than did the crossed-screw construct. There was a significant correlation (crossed-screw construct: p = 0.014; plate-and-screw construct: p = 0.010) between BMD and the number of cycles to failure. CONCLUSION: Under cyclic loading conditions, the construct using a medial locking plate with adjunct compression screw was superior to the construct using two crossed screws. CLINICAL RELEVANCE: The medial locking-plate technique described could help shorten the period of nonweightbearing and reduce the risk of non-union.
Authors: Nicholas A Russell; Gianmarco Regazzola; Amiethab Aiyer; Tomohiro Nomura; Matthew H Pelletier; Mark Myerson; William R Walsh Journal: Front Surg Date: 2015-12-14
Authors: Maximilian F Kasparek; Emir Benca; Lena Hirtler; Madeleine Willegger; Friedrich Boettner; Shahin Zandieh; Johannes Holinka; Reinhard Windhager; Reinhard Schuh Journal: Int Orthop Date: 2022-07-18 Impact factor: 3.479
Authors: Rene Burchard; Robin Massa; Christian Soost; Wolfgang Richter; Gerhard Dietrich; Arne Ohrndorf; Hans-Jürgen Christ; Claus-Peter Fritzen; Jan Adriaan Graw; Jan Schmitt Journal: J Orthop Surg Res Date: 2018-07-11 Impact factor: 2.359