Judy Jin1, Steve Schomisch, Michael J Rosen. 1. Department of Surgery, Case Comprehensive Hernia Center, University Hospitals Case Medical Center, Cleveland, Ohio 44106, USA.
Abstract
INTRODUCTION: Seroma formation is one of the most common post operative complications related to abdominal wall hernia repairs with mesh. We hypothesized that the different biomaterials used to construct commonly used prosthetic mesh may influence permeability to fluid and affect seroma formation rates. METHODS: We designed an in vitro study where a 5 cm piece of mesh was placed in a closed system where normal saline was forced across the mesh and the pressure (mmHg) required for a constant stream of fluid was recorded. Eight prosthetic materials were studied: polyester/oxidized collagen (PC), expanded PTFE (DM), polypropylene/ePTFE (BC), polypropylene/oxidized cellulose (PR), light weight polypropylene/omega 3 fatty acid (CQ), compressed PTFE (MM), polypropylene (PP) and polyester (P) mesh. RESULTS: Each mesh was tested five times and the results averaged. The 3 meshes without anti-adhesive barriers (MM, PP, P) had fluid move across with minimal pressure (<1 mmHg). For the intraperitoneal mesh, there was a significant difference in pressure necessary for fluid movement (PR = 3.6, CQ = 36, PC = 56.6, DM > 350, BC > 350 mmHg, p = <0.001). However, the fenestrations at the suture lines necessary to combine the PP and DM in the BC mesh permitted fluid transport at low pressures (<1 mmHg). CONCLUSION: Based on our in vitro study, each mesh exhibited different fluid permeability, especially in the case of meshes with anti-adhesive barriers. This study also infers that methods to create pressure gradients across mesh, such as an abdominal binder, may reduce seroma formation of certain meshes.
INTRODUCTION:Seroma formation is one of the most common post operative complications related to abdominal wall hernia repairs with mesh. We hypothesized that the different biomaterials used to construct commonly used prosthetic mesh may influence permeability to fluid and affect seroma formation rates. METHODS: We designed an in vitro study where a 5 cm piece of mesh was placed in a closed system where normal saline was forced across the mesh and the pressure (mmHg) required for a constant stream of fluid was recorded. Eight prosthetic materials were studied: polyester/oxidized collagen (PC), expanded PTFE (DM), polypropylene/ePTFE (BC), polypropylene/oxidized cellulose (PR), light weight polypropylene/omega 3 fatty acid (CQ), compressed PTFE (MM), polypropylene (PP) and polyester (P) mesh. RESULTS: Each mesh was tested five times and the results averaged. The 3 meshes without anti-adhesive barriers (MM, PP, P) had fluid move across with minimal pressure (<1 mmHg). For the intraperitoneal mesh, there was a significant difference in pressure necessary for fluid movement (PR = 3.6, CQ = 36, PC = 56.6, DM > 350, BC > 350 mmHg, p = <0.001). However, the fenestrations at the suture lines necessary to combine the PP and DM in the BC mesh permitted fluid transport at low pressures (<1 mmHg). CONCLUSION: Based on our in vitro study, each mesh exhibited different fluid permeability, especially in the case of meshes with anti-adhesive barriers. This study also infers that methods to create pressure gradients across mesh, such as an abdominal binder, may reduce seroma formation of certain meshes.
Authors: A Poli; F Parisi; F Millanta; L Solfanelli; P García-Pastor; C Magliaro; V Miragliotta; S Burchielli Journal: Hernia Date: 2019-11-26 Impact factor: 4.739
Authors: Gemma Pascual; Marta Rodríguez; Bárbara Pérez-Köhler; Claudia Mesa-Ciller; Mar Fernández-Gutiérrez; Julio San Román; Juan M Bellón Journal: J Mater Sci Mater Med Date: 2017-02-16 Impact factor: 3.896