Literature DB >> 17416461

Copper and cadmium adsorption on pellets made from fired coal fly ash.

A Papandreou1, C J Stournaras, D Panias.   

Abstract

Studies on the utilization of low cost adsorbents for removal of heavy metals from wastewaters are gaining attention. Fired coal fly ash, a solid by-product that is produced in power plants worldwide in million of tonnes, has attracted researchers' interest. In this work, fly ash was shaped into pellets that have diameter in-between 3-8mm, high relative porosity and very good mechanical strength. The pellets were used in adsorption experiments for the removal of copper and cadmium ions from aqueous solutions. The effect of agitation rate, equilibration time, pH of solution and initial metal concentration were studied. The adsorption of both cations follows pseudo-second order kinetics reaching equilibrium after an equilibration time of 72 h. The experimental results for copper and cadmium adsorption fit well to a Langmuirian type isotherm. The calculated adsorption capacities of pellets for copper and cadmium were 20.92 and 18.98 mg/g, respectively. Desorption experiments were performed in several extraction media. The results showed that both metals were desorbed substantially from pellets under acidic solutions. For this reason, metal saturated pellets were encapsulated in concrete blocks synthesized from cement and raw pulverized fly ash in order to avoid metal desorption. The heavy metals immobilization after encapsulation in concrete blocks was tested through desorption tests in several aqueous media. The results showed that after 2 months in acidic media with pH 2.88 and 4.98 neither copper nor cadmium were desorbed thus indicating excellent stabilization of heavy metals in the concrete matrix. As a conclusion, the results showed that fly ash shaped into pellets could be considered as a potential adsorbent for the removal of copper and cadmium from wastewaters. Moreover, the paper proposes an efficient and simple stabilization process of the utilized adsorbents thus guarantying their safe disposal in industrial landfills and eliminating the risk of pollution for groundwater and other natural water receivers.

Entities:  

Mesh:

Substances:

Year:  2007        PMID: 17416461     DOI: 10.1016/j.jhazmat.2007.03.020

Source DB:  PubMed          Journal:  J Hazard Mater        ISSN: 0304-3894            Impact factor:   10.588


  5 in total

1.  Use of fly ash agglomerates for removal of arsenic.

Authors:  Izabela Polowczyk; Anna Bastrzyk; Tomasz Koźlecki; Wojciech Sawiński; Piotr Rudnicki; Adam Sokołowski; Zygmunt Sadowski
Journal:  Environ Geochem Health       Date:  2010-04-10       Impact factor: 4.609

2.  Removal of copper from water by electrocoagulation process--effect of alternating current (AC) and direct current (DC).

Authors:  Ramakrishnan Kamaraj; Pandian Ganesan; Jothinathan Lakshmi; Subramanyan Vasudevan
Journal:  Environ Sci Pollut Res Int       Date:  2012-03-17       Impact factor: 4.223

3.  Use of Eggshell-Catalyzed Biochar Adsorbents for Pb Removal from Aqueous Solution.

Authors:  Dongdong Liu; Zhengkai Hao; Dengqian Chen; Lipeng Jiang; Tianqi Li; Bing Tian; Cuiping Yan; Yuan Luo; Guang Chen; Hongfu Ai
Journal:  ACS Omega       Date:  2022-06-14

4.  Cadmium Removal from Contaminated Water Using Polyelectrolyte-Coated Industrial Waste Fly Ash.

Authors:  Fatai A Olabemiwo; Bassam S Tawabini; Faheemuddin Patel; Tajudeen A Oyehan; Mazen Khaled; Tahar Laoui
Journal:  Bioinorg Chem Appl       Date:  2017-06-07       Impact factor: 7.778

Review 5.  Recent advances in dye and metal ion removal using efficient adsorbents and novel nano-based materials: an overview.

Authors:  Ahmad K Badawi; M Abd Elkodous; Gomaa A M Ali
Journal:  RSC Adv       Date:  2021-11-11       Impact factor: 4.036

  5 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.