Literature DB >> 17406916

Optimal biocatalyst loading in a fixed bed.

V Tortoriello1, G B DeLancey.   

Abstract

The optimal distribution of biocatalyst in a fixed bed operating at steady state was determined to minimize the length of the bed for a fixed conversion of 95%. The distribution in terms of the biocatalyst loading on an inert support depends upon the axial distance from the bed entrance (continuous solution) as well as a set of dimensionless parameters that reflect the bed geometry, the bulk flow, reaction kinetics and diffusional characteristics. A mathematical model of the system with the following features was used to obtain the results: (1) convective mass transfer and dispersion in the bulk phase; (2) mass transfer from the bulk phase to the surface of the catalyst particle; and (3) simultaneous diffusion and chemical reaction in the catalyst particle with Michaelis-Menton kinetics and a reliable diffusion model (Zhao and DeLancey in Biotechnol Bioeng 64:434-441, 1999, 2000). The solution to the mathematical model was obtained with Mathematica utilizing the Runge Kutta 4-5 method. The dimensionless length resulting from the continuous solution was compared with the optimal length restricted to a uniform or constant cell loading across the entire bed. The maximum difference in the dimensionless length between the continuous and uniform solutions was determined to be 6.5%. The model was applied to published conversion data for the continuous production of ethanol that included cell loading (Taylor et al. in Biotechnol Prog 15:740-751, 2002). The data indicated a minimum production cost at a catalyst loading within 10% of the optimum predicted by the mathematical model. The production rate versus cell loading in most cases displayed a sufficiently broad optimum that the same (non-optimal) rate could be obtained at a significantly smaller loading such as a rate at 80% loading being equal to the rate at 20% loading. These results are particularly important because of the renewed interest in ethanol production (Novozymes and BBI International, Fuel ethanol: a technological evolution, 2004).

Entities:  

Mesh:

Year:  2007        PMID: 17406916     DOI: 10.1007/s10295-007-0217-5

Source DB:  PubMed          Journal:  J Ind Microbiol Biotechnol        ISSN: 1367-5435            Impact factor:   4.258


  6 in total

1.  Transmembrane distribution of substrate and product during the bioreduction of acetophenone with resting cells of Saccharomyces cerevisiae.

Authors:  Y Zhao; G B DeLancey
Journal:  Biotechnol Bioeng       Date:  1999-08-20       Impact factor: 4.530

2.  Dry-grind process for fuel ethanol by continuous fermentation and stripping.

Authors:  F Taylor; M J Kurantz; N Goldberg; A J McAloon; J C Craig
Journal:  Biotechnol Prog       Date:  2000 Jul-Aug

3.  A diffusion model and optimal cell loading for immobilized cell biocatalysts.

Authors:  Y Zhao; G B Delancey
Journal:  Biotechnol Bioeng       Date:  2000-09-20       Impact factor: 4.530

4.  Diffusion in gels containing immobilized cells: a critical review.

Authors:  B A Westrin; A Axelsson
Journal:  Biotechnol Bioeng       Date:  1991-08-20       Impact factor: 4.530

5.  The effective diffusive permeability of a nonreacting solute in microbial cell aggregates.

Authors:  S B Libicki; P M Salmon; C R Robertson
Journal:  Biotechnol Bioeng       Date:  1988-06-20       Impact factor: 4.530

6.  Stereoselective bioconversions in continuously operated fixed bed reactors: Modeling and process optimization.

Authors:  M Indlekofer; F Brotz; A Bauer; M Reuss
Journal:  Biotechnol Bioeng       Date:  1996-11-20       Impact factor: 4.530

  6 in total
  1 in total

Review 1.  Microbial diversity and genomics in aid of bioenergy.

Authors:  Vipin Chandra Kalia; Hemant J Purohit
Journal:  J Ind Microbiol Biotechnol       Date:  2008-01-10       Impact factor: 3.346

  1 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.