Literature DB >> 17279905

Viscous froth lens.

T E Green1, A Bramley, L Lue, P Grassia.   

Abstract

Microscale models of foam structure traditionally incorporate a balance between bubble pressures and surface tension forces associated with curvature of bubble films. In particular, models for flowing foam microrheology have assumed this balance is maintained under the action of some externally imposed motion. Recently, however, a dynamic model for foam structure has been proposed, the viscous froth model, which balances the net effect of bubble pressures and surface tension to viscous dissipation forces: this permits the description of fast-flowing foam. This contribution examines the behavior of the viscous froth model when applied to a paradigm problem with a particularly simple geometry: namely, a two-dimensional bubble "lens." The lens consists of a channel partly filled by a bubble (known as the "lens bubble") which contacts one channel wall. An additional film (known as the "spanning film") connects to this bubble spanning the distance from the opposite channel wall. This simple structure can be set in motion and deformed out of equilibrium by applying a pressure across the spanning film: a rich dynamical behavior results. Solutions for the lens structure steadily propagating along the channel can be computed by the viscous froth model. Perturbation solutions are obtained in the limit of a lens structure with weak applied pressures, while numerical solutions are available for higher pressures. These steadily propagating solutions suggest that small lenses move faster than large ones, while both small and large lens bubbles are quite resistant to deformation, at least for weak applied back pressures. As the applied back pressure grows, the structure with the small lens bubble remains relatively stiff, while that with the large lens bubble becomes much more compliant. However, with even further increases in the applied back pressure, a critical pressure appears to exist for which the steady-state structure loses stability and unsteady-state numerical simulations show it breaks up by route of a topological transformation.

Year:  2006        PMID: 17279905     DOI: 10.1103/PhysRevE.74.051403

Source DB:  PubMed          Journal:  Phys Rev E Stat Nonlin Soft Matter Phys        ISSN: 1539-3755


  7 in total

1.  A foam film propagating in a confined geometry: analysis via the viscous froth model.

Authors:  P Grassia; G Montes-Atenas; L Lue; T E Green
Journal:  Eur Phys J E Soft Matter       Date:  2008-02-12       Impact factor: 1.890

2.  Foam-improved oil recovery: Modelling the effect of an increase in injection pressure.

Authors:  Elizabeth Mas Hernández; Paul Grassia; Nima Shokri
Journal:  Eur Phys J E Soft Matter       Date:  2015-06-30       Impact factor: 1.890

3.  Foam front propagation in anisotropic oil reservoirs.

Authors:  P Grassia; C Torres-Ulloa; S Berres; E Mas-Hernández; N Shokri
Journal:  Eur Phys J E Soft Matter       Date:  2016-04-20       Impact factor: 1.890

4.  Effect of surfactant redistribution on the flow and stability of foam films.

Authors:  Denny Vitasari; Simon Cox; Paul Grassia; Ruben Rosario
Journal:  Proc Math Phys Eng Sci       Date:  2020-02-12       Impact factor: 2.704

5.  Pressure-driven growth in strongly heterogeneous systems.

Authors:  P Grassia
Journal:  Eur Phys J E Soft Matter       Date:  2018-01-25       Impact factor: 1.890

6.  Analysis of a model for surfactant transport around a foam meniscus.

Authors:  P Grassia
Journal:  Proc Math Phys Eng Sci       Date:  2022-06-29       Impact factor: 3.213

7.  Viscous froth model applied to the motion and topological transformations of two-dimensional bubbles in a channel: three-bubble case.

Authors:  C Torres-Ulloa; P Grassia
Journal:  Proc Math Phys Eng Sci       Date:  2022-02-09       Impact factor: 2.704

  7 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.