Literature DB >> 17154478

Composition dependence of the crystallization behavior and morphology of the poly(ethylene oxide)-poly(epsilon-caprolactone) diblock copolymer.

Chaoliang He1, Jingru Sun, Jia Ma, Xuesi Chen, Xiabin Jing.   

Abstract

The crystallization behavior and morphology of the crystalline-crystalline poly(ethylene oxide)-poly(epsilon-caprolactone) diblock copolymer (PEO-b-PCL) was studied by differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD), Fourier transform infrared spectroscopy (FTIR), small-angle X-ray scattering (SAXS), and hot-stage polarized optical microscope (POM). The mutual effects between the PEO and PCL blocks were significant, leading to the obvious composition dependence of the crystallization behavior and morphology of PEO-b-PCL. In this study, the PEO block length was fixed (Mn = 5000) and the weight ratio of PCL/PEO was tailored by changing the PCL block length. Both blocks could crystallize in PEO-b-PCL with the PCL weight fraction (WFPCL) of 0.23-0.87. For the sample with the WFPCL of 0.36 or less, the PEO block crystallized first, resulting in the obvious confinement of the PCL block and vice versa for the sample with WFPCL of 0.43 or more. With increasing WFPCL, the crystallinity of PEO reduced continuously while the variation of the PCL crystallinity exhibited a maximum. The long period of PEO-b-PCL increased with increasing WFPCL from 0.16 to 0.50 but then decreased with the further increase of WFPCL due to the interaction of the respective variation of the thicknesses of the PEO and PCL crystalline lamellae. Only the PEO spherulites were observed in samples with WFPCL of 0.16-0.36 by POM, in contrast to only the PCL spherulites in samples with WFPCL of 0.56-0.87. For samples with WFPCL of 0.43 and 0.50, a unique concentric spherulite was observed. The morphology of the inner and outer portions of the concentric spherulites was determined by the PCL and PEO spherulites, respectively. The growth rate of the PEO spherulites reduced rapidly with increasing WFPCL from 0 to 0.50. However, when increasing WFPCL from 0.43 to 0.87, the variation of the growth rate of the PCL spherulites exhibited a maximum rather than a monotonic change.

Entities:  

Mesh:

Substances:

Year:  2006        PMID: 17154478     DOI: 10.1021/bm060578m

Source DB:  PubMed          Journal:  Biomacromolecules        ISSN: 1525-7797            Impact factor:   6.988


  5 in total

1.  Synthesis and characterization of poly(ethylene glycol) bottlebrush networks via ring-opening metathesis polymerization.

Authors:  Brandon R Clarke; Gregory N Tew
Journal:  J Polym Sci (2020)       Date:  2022-01-31

2.  Study of temperature dependence of crystallisation transitions of a symmetric PEO-PCL diblock copolymer using simultaneous SAXS and WAXS measurements with synchrotron radiation.

Authors:  Shichun Jiang; Chaoliang He; Yongfeng Men; Xuesi Chen; Lijia An; Sérgio S Funari; Chi-Ming Chan
Journal:  Eur Phys J E Soft Matter       Date:  2008-11-19       Impact factor: 1.890

3.  Crystallization and Temperature Driven Morphological Evolution of Bio-based Polyethylene Glycol-acrylic Rosin Polymer.

Authors:  Yanzhi Zhao; Mengjun Zou; Huazhen Liao; Fangkai Du; Fuhou Lei; Xuecai Tan; Jinyan Zhang; Qin Huang; Juying Zhou
Journal:  Polymers (Basel)       Date:  2019-10-15       Impact factor: 4.329

4.  Effect of polyvinyl acetals on non-isothermal crystallization behaviour and mechanical properties of poly(ε-caprolactone).

Authors:  Biao Yang; Xin Zhang; Chun Wang; Ran Liu; Baomin Fan; Huijuan Zhang; Hui Sun
Journal:  RSC Adv       Date:  2019-11-12       Impact factor: 4.036

5.  Design and Development of D‒α‒Tocopheryl Polyethylene Glycol Succinate‒block‒Poly(ε-Caprolactone) (TPGS-b-PCL) Nanocarriers for Solubilization and Controlled Release of Paclitaxel.

Authors:  Osman Yusuf; Raisuddin Ali; Abdullah H Alomrani; Aws Alshamsan; Abdullah K Alshememry; Abdulaziz M Almalik; Afsaneh Lavasanifar; Ziyad Binkhathlan
Journal:  Molecules       Date:  2021-05-04       Impact factor: 4.411

  5 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.