OBJECTIVES: The development of yttrium oxide partially stabilized zirconia (Y-TZP) has allowed the use of ceramic in load-bearing sites. The aim of this study was to evaluate and compare the biaxial flexural strength, hardness and fatigue life of colored and uncolored zirconia in the LAVAtrade mark system. MATERIALS AND METHODS: Eight groups (n=30) of standardized disc specimens (15mmx1.3mm) were used to examine the biaxial flexural strength (ISO 6872 standard) using a Dartec HC10 Fatigue Tester (Zwick Ltd., UK) and Vickers hardness was also measured. The uncolored, FS4, FS7 groups were also submitted to dynamic fatigue testing to produce stress-number curves. The strength reliability was analyzed using Weibull distribution. RESULTS: All groups had a mean biaxial flexural strength, hardness and Weibull modulus (m) of approximately 1100MPa, 1300HV and 9.8-12.9, respectively. One-way analysis of variance (ANOVA) showed no significant difference in biaxial flexural strength among the eight groups (p>0.05). Two-way ANOVA showed no significant differences in hardness values among groups except FS1 and FS5 which had significantly higher hardness values than FS4 and FS7 (p<0.001) and FS5 also had a higher hardness value than FS3 (p<0.05). Additionally, uncolored, FS4 and FS7 survived at 5x10(5) cycles at a stress level in the range of 60-65% of the mean biaxial flexural strength. CONCLUSION: There was no difference in flexural strength of uncolored and colored Y-TZP ceramic. The fatigue limit of uncolored, FS4 and FS7 zirconia may be defined as lying between 60 and 65% of the stress to failure.
OBJECTIVES: The development of yttrium oxide partially stabilized zirconia (Y-TZP) has allowed the use of ceramic in load-bearing sites. The aim of this study was to evaluate and compare the biaxial flexural strength, hardness and fatigue life of colored and uncolored zirconia in the LAVAtrade mark system. MATERIALS AND METHODS: Eight groups (n=30) of standardized disc specimens (15mmx1.3mm) were used to examine the biaxial flexural strength (ISO 6872 standard) using a Dartec HC10 Fatigue Tester (Zwick Ltd., UK) and Vickers hardness was also measured. The uncolored, FS4, FS7 groups were also submitted to dynamic fatigue testing to produce stress-number curves. The strength reliability was analyzed using Weibull distribution. RESULTS: All groups had a mean biaxial flexural strength, hardness and Weibull modulus (m) of approximately 1100MPa, 1300HV and 9.8-12.9, respectively. One-way analysis of variance (ANOVA) showed no significant difference in biaxial flexural strength among the eight groups (p>0.05). Two-way ANOVA showed no significant differences in hardness values among groups except FS1 and FS5 which had significantly higher hardness values than FS4 and FS7 (p<0.001) and FS5 also had a higher hardness value than FS3 (p<0.05). Additionally, uncolored, FS4 and FS7 survived at 5x10(5) cycles at a stress level in the range of 60-65% of the mean biaxial flexural strength. CONCLUSION: There was no difference in flexural strength of uncolored and colored Y-TZP ceramic. The fatigue limit of uncolored, FS4 and FS7 zirconia may be defined as lying between 60 and 65% of the stress to failure.
Authors: Susanne S Scherrer; Maria Cattani-Lorente; Eric Vittecoq; François de Mestral; Jason A Griggs; H W Anselm Wiskott Journal: Dent Mater Date: 2010-11-05 Impact factor: 5.304