BACKGROUND: Marginal hard tissue defects present at implants with a rough surface can heal with a high degree of bone fill and osseointegration. The healing of similar defects adjacent to implants with a smooth surface appears to be less predictable. OBJECTIVE: The aim was to compare bone healing at implants with turned or rough surface topographies placed in self-contained defects using either a submerged or non-submerged installation technique. MATERIAL AND METHODS: Six dogs were used. Three months after tooth extraction four experimental sites were prepared for implant installation in both sides of the mandible. The marginal 5 mm of the canal prepared for the implant was widened. Thus, following implant placement a circumferential gap occurred between the bone tissue and the implant surface that was between 1 and 1.25 mm wide. In each side of the mandible two implants with a turned surface and two implants with a rough surface were installed. The implants in the right side were fully submerged, while a non-submerged technique was applied in the left side. The animals were sacrificed 4 months later, block biopsies of each implant site were dissected and ground as well as paraffin sections were prepared. RESULTS: The marginal defects around rough surface implants exhibited after 4 months of healing substantial bone fill and a high degree of osseointegration following either the submerged or the non-submerged installation technique. Healing at turned implants was characterized by incomplete bone fill and the presence of a connective tissue zone between the implant and the newly formed bone. The distance between the implant margin (M) and the most coronal level of bone-to-implant contact (B) at implants with a rough surface was 0.84+/-0.37 mm at submerged and 0.90+/-0.39 mm at non-submerged sites. The distance M-B at implants with a turned surface was 3.39+/-0.52 mm at submerged and 3.23+/-0.68 mm at non-submerged sites. The differences between the rough and turned implants regarding the length of distance M-B were statistically significant (paired t-test). CONCLUSION: Osseointegration at implants placed in sites with marginal defects is influenced by the surface characteristics of the implant.
BACKGROUND: Marginal hard tissue defects present at implants with a rough surface can heal with a high degree of bone fill and osseointegration. The healing of similar defects adjacent to implants with a smooth surface appears to be less predictable. OBJECTIVE: The aim was to compare bone healing at implants with turned or rough surface topographies placed in self-contained defects using either a submerged or non-submerged installation technique. MATERIAL AND METHODS: Six dogs were used. Three months after tooth extraction four experimental sites were prepared for implant installation in both sides of the mandible. The marginal 5 mm of the canal prepared for the implant was widened. Thus, following implant placement a circumferential gap occurred between the bone tissue and the implant surface that was between 1 and 1.25 mm wide. In each side of the mandible two implants with a turned surface and two implants with a rough surface were installed. The implants in the right side were fully submerged, while a non-submerged technique was applied in the left side. The animals were sacrificed 4 months later, block biopsies of each implant site were dissected and ground as well as paraffin sections were prepared. RESULTS: The marginal defects around rough surface implants exhibited after 4 months of healing substantial bone fill and a high degree of osseointegration following either the submerged or the non-submerged installation technique. Healing at turned implants was characterized by incomplete bone fill and the presence of a connective tissue zone between the implant and the newly formed bone. The distance between the implant margin (M) and the most coronal level of bone-to-implant contact (B) at implants with a rough surface was 0.84+/-0.37 mm at submerged and 0.90+/-0.39 mm at non-submerged sites. The distance M-B at implants with a turned surface was 3.39+/-0.52 mm at submerged and 3.23+/-0.68 mm at non-submerged sites. The differences between the rough and turned implants regarding the length of distance M-B were statistically significant (paired t-test). CONCLUSION: Osseointegration at implants placed in sites with marginal defects is influenced by the surface characteristics of the implant.
Authors: Peer W Kämmerer; Malte Scholz; Maria Baudisch; Jan Liese; Katharina Wegner; Bernhard Frerich; Hermann Lang Journal: Stem Cells Int Date: 2017-08-16 Impact factor: 5.443
Authors: Adrián Maximiano Millán; Rocío Bravo Álvarez; Miguel Plana Montori; María Guerrero González; David Saura García-Martín; Blanca Ríos-Carrasco; Francesca Monticelli; José Vicente Ríos-Santos; Ana Fernández-Palacín Journal: Int J Environ Res Public Health Date: 2020-03-14 Impact factor: 3.390