Literature DB >> 15015210

Effects of various sterilization methods on the setting and mechanical properties of apatite cement.

Masaaki Takechi1, Youji Miyamoto, Yukihiro Momota, Tetsuya Yuasa, Seiko Tatehara, Masaru Nagayama, Kunio Ishikawa.   

Abstract

Sterilization capability is a necessary requirement for any material that is to be used in a medical application. Therefore, it is necessary for apatite cement (AC) to be sterilized. Because there is little information on the sterilization methods of AC, the aims of this investigation were to evaluate the effects of various sterilization methods, including steam, dry heat, ethylene oxide (EtO) gas, and gamma irradiation sterilizations, on the setting and mechanical properties of AC. In the case of steam sterilization, because AC powder aggregated before setting-time measurements, the setting time could not be measured. When the powder was sterilized by dry heat or EtO gas, the setting time was prolonged significantly and the wet diametral tensile strength (DTS) value decreased significantly. Therefore, sterilizations with steam, dry heat, or EtO gas were suggested to be inappropriate methods for AC. Accordingly, the following experiments focused on gamma sterilization. The setting time of AC was retarded with an increase in gamma irradiation dose. The wet DTS value decreased with the increase in gamma irradiation dose. There was no compositional change due to the gamma irradiation. The following tests were carried out in order to examine the effect of the gamma irradiation on the setting reaction of AC in detail. Tetracalcium phosphate [TTCP: Ca(4)(PO(4))(2)O] and dicalcium phosphate anhydrous (DCPA: CaHPO(4)) were separately irradiated, and the cements were produced with the use of irradiated powder and nonirradiated powder. Although the wet DTS value of AC produced from irradiated TTCP and nonirradiated DCPA decreased with increasing gamma irradiation dose, there was no significant difference. In contrast, the wet DTS value of AC produced from irradiated DCPA and nonirradiated TTCP significantly decreased with the increase in gamma irradiation dose. In conclusion, although the detailed mechanism of the delayed setting time and decreased DTS value was not clarified by the present study, it was found that gamma irradiation affected DCPA more than TTCP. Copyright 2004 Wiley Periodicals, Inc.

Entities:  

Mesh:

Substances:

Year:  2004        PMID: 15015210     DOI: 10.1002/jbm.b.10031

Source DB:  PubMed          Journal:  J Biomed Mater Res B Appl Biomater        ISSN: 1552-4973            Impact factor:   3.368


  6 in total

Review 1.  Calcium Phosphate Bioceramics: A Review of Their History, Structure, Properties, Coating Technologies and Biomedical Applications.

Authors:  Noam Eliaz; Noah Metoki
Journal:  Materials (Basel)       Date:  2017-03-24       Impact factor: 3.623

2.  Basic research on aw-AC/PLGA composite scaffolds for bone tissue engineering.

Authors:  Shiho Minamiguchi; Masaaki Takechi; Tetsuya Yuasa; Yukihiro Momota; Seiko Tatehara; Hideyuki Takano; Youji Miyamoto; Kazuhito Satomura; Masaru Nagayama
Journal:  J Mater Sci Mater Med       Date:  2007-08-15       Impact factor: 3.896

3.  Self-setting calcium orthophosphate formulations.

Authors:  Sergey V Dorozhkin
Journal:  J Funct Biomater       Date:  2013-11-12

4.  Direct and interactive influence of explanatory variables on properties of a calcium phosphate cement for vertebral body augmentation.

Authors:  Daniel M Werdofa; Gladius Lewis
Journal:  J Mater Sci Mater Med       Date:  2013-09-18       Impact factor: 3.896

5.  Influences of the steam sterilization on the properties of calcium phosphate porous bioceramics.

Authors:  Xiangfeng Li; Bo Guo; Yumei Xiao; Tun Yuan; Yujiang Fan; Xingdong Zhang
Journal:  J Mater Sci Mater Med       Date:  2015-11-26       Impact factor: 3.896

6.  Calcium Phosphate Bone Cements Including Sugar Surfactants: Part One-Porosity, Setting Times and Compressive Strength.

Authors:  Ariane Bercier; Stéphane Gonçalves; Olivier Lignon; Juliette Fitremann
Journal:  Materials (Basel)       Date:  2010-09-30       Impact factor: 3.623

  6 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.