Arzu Tezvergil1, Lippo V J Lassila, Pekka K Vallittu. 1. Department of Prosthetic Dentistry and Biomaterials Research, Institute of Dentistry, University of Turku, Lemminkäisenkatu 2, 20520 Turku, Finland. arztez@utu.fi
Abstract
OBJECTIVES: The aim of this study was to characterize the thermal expansion and dimensional changes of fiber-reinforced composite (FRC) according to the fiber orientation, brand of FRC product and polymerization conditions. METHODS: Cubic specimens (n=5) were prepared from different brands of FRC and particulate filler composites and dimethacrylate monomer resin. The specimens were polymerized with a light-curing device for 40 s or additionally with prolonged polymerization in the light-curing oven for 15 min. Linear coefficients of thermal expansion (LCTE) values for different materials and for FRC with different fiber orientations were determined using a thermomechanical analyzer. RESULTS: All specimens exhibited linear increase in the value of LCTE between 37 and 67 degrees C. The analysis of ANOVA revealed that orientation of fiber and brand of material had significant effect (P<0.001) on LCTE values for 37-67 degrees C interval. Some interaction between factors also existed. Also, temperature interval 110-150 degrees C had significant effect on the LCTE values according to the curing unit, brand and orientation of fibers. SIGNIFICANCE: The results of this study suggest that the anisotropic nature of FRC exists also with regard to thermal expansion. The variation of LCTE of FRC compared to that of particulate filler composites might influence the interfacial adhesion of FRC appliances.
OBJECTIVES: The aim of this study was to characterize the thermal expansion and dimensional changes of fiber-reinforced composite (FRC) according to the fiber orientation, brand of FRC product and polymerization conditions. METHODS: Cubic specimens (n=5) were prepared from different brands of FRC and particulate filler composites and dimethacrylate monomer resin. The specimens were polymerized with a light-curing device for 40 s or additionally with prolonged polymerization in the light-curing oven for 15 min. Linear coefficients of thermal expansion (LCTE) values for different materials and for FRC with different fiber orientations were determined using a thermomechanical analyzer. RESULTS: All specimens exhibited linear increase in the value of LCTE between 37 and 67 degrees C. The analysis of ANOVA revealed that orientation of fiber and brand of material had significant effect (P<0.001) on LCTE values for 37-67 degrees C interval. Some interaction between factors also existed. Also, temperature interval 110-150 degrees C had significant effect on the LCTE values according to the curing unit, brand and orientation of fibers. SIGNIFICANCE: The results of this study suggest that the anisotropic nature of FRC exists also with regard to thermal expansion. The variation of LCTE of FRC compared to that of particulate filler composites might influence the interfacial adhesion of FRC appliances.
Authors: Aous A Abdulmajeed; Jaana Willberg; Stina Syrjänen; Pekka K Vallittu; Timo O Närhi Journal: J Mater Sci Mater Med Date: 2015-01-15 Impact factor: 3.896
Authors: Kacper Kroczek; Paweł Turek; Damian Mazur; Jacek Szczygielski; Damian Filip; Robert Brodowski; Krzysztof Balawender; Łukasz Przeszłowski; Bogumił Lewandowski; Stanisław Orkisz; Artur Mazur; Grzegorz Budzik; Józef Cebulski; Mariusz Oleksy Journal: Polymers (Basel) Date: 2022-04-09 Impact factor: 4.967
Authors: Massimo Corsalini; Francesco Pettini; Daniela Di Venere; Andrea Ballini; Giuseppe Chiatante; Luciano Lamberti; Carmine Pappalettere; Michele Fiorentino; Antonio E Uva; Giuseppe Monno; Antonio Boccaccio Journal: Open Dent J Date: 2016-11-16
Authors: Maximiliano Sérgio Cenci; Paulo Antônio da Rosa Rodolpho; Tatiana Pereira-Cenci; Altair Antoninha Del Bel Cury; Flávio Fernando Demarco Journal: J Appl Oral Sci Date: 2010 Jul-Aug Impact factor: 2.698