M Ozcan1, H N Alkumru, D Gemalmaz. 1. Department of Prosthodontics, Faculty of Dentistry, Marmara University, Istanbul, Turkey. mutluozcan@hotmail.com
Abstract
PURPOSE: The aim of this study was to evaluate the effect of three different surface treatments on the bond strength of four different luting cements--three bis-GMA-based resin cements and a compomer cement--to In-Ceram. MATERIALS AND METHODS: Eight In-Ceram samples were used for each experimental group. The samples were randomly assigned three treatment conditions: (1) etching for 90 seconds with 5% hydrofluoric acid gel, (2) sandblasting (110-micron Al2O3), and (3) tribochemical silica coating. All samples were silanated following the surface treatment. The luting cements were bonded to In-Ceram specimens using Teflon tubes. All samples were thermocycled for 5,000 cycles altering between 5 and 55 degrees C with 30-second dwell times. The shear bond strength values were measured in a universal testing machine with a cross-head speed of 1 mm/min. Analysis of variance was used to analyze data. RESULTS: The mean bond strengths varied between 1.2 and 24.7 MPa. CONCLUSION:Shear bond strength of compomer cement following tribochemical silica coating was significantly lower in comparison to resin cements. Luting of In-Ceram with various resins provided varying degrees of bond strengths that were significantly increased by the tribochemical silica-coating system.
RCT Entities:
PURPOSE: The aim of this study was to evaluate the effect of three different surface treatments on the bond strength of four different luting cements--three bis-GMA-based resin cements and a compomer cement--to In-Ceram. MATERIALS AND METHODS: Eight In-Ceram samples were used for each experimental group. The samples were randomly assigned three treatment conditions: (1) etching for 90 seconds with 5% hydrofluoric acid gel, (2) sandblasting (110-micron Al2O3), and (3) tribochemical silica coating. All samples were silanated following the surface treatment. The luting cements were bonded to In-Ceram specimens using Teflon tubes. All samples were thermocycled for 5,000 cycles altering between 5 and 55 degrees C with 30-second dwell times. The shear bond strength values were measured in a universal testing machine with a cross-head speed of 1 mm/min. Analysis of variance was used to analyze data. RESULTS: The mean bond strengths varied between 1.2 and 24.7 MPa. CONCLUSION: Shear bond strength of compomer cement following tribochemical silica coating was significantly lower in comparison to resin cements. Luting of In-Ceram with various resins provided varying degrees of bond strengths that were significantly increased by the tribochemical silica-coating system.
Authors: Tevfik Yavuz; Erhan Dilber; Haluk Baris Kara; Ali Riza Tuncdemir; A Nilgun Ozturk Journal: Lasers Med Sci Date: 2012-09-13 Impact factor: 3.161
Authors: Ahmed El Gamal; Etienne Medioni; Jean Paul Rocca; Carlo Fornaini; Omid H Muhammad; Nathalie Brulat-Bouchard Journal: Lasers Med Sci Date: 2017-03-09 Impact factor: 3.161
Authors: Carlos de Paula Eduardo; Marina Stella Bello-Silva; Simone Gonçalves Moretto; Paulo Francisco Cesar; Patricia Moreira de Freitas Journal: Lasers Med Sci Date: 2010-08-25 Impact factor: 3.161
Authors: Susana María Salazar Marocho; Mutlu Ozcan; Regina Amaral; Luiz Felipe Valandro; Marco Antonio Bottino Journal: Clin Oral Investig Date: 2012-01-13 Impact factor: 3.573
Authors: Markus B Blatz; Jin-Ho Phark; Fusun Ozer; Francis K Mante; Najeed Saleh; Michael Bergler; Avishai Sadan Journal: Clin Oral Investig Date: 2009-05-05 Impact factor: 3.573