PURPOSE: To evaluate resin bond strength to enamel contaminated with handpiece oil. MATERIALS AND METHODS: Bovine teeth were randomly assigned to six groups of 20 teeth each for treatment with one of six different bonding systems (five one-bottle and one multibottle). For each system, 10 enamel specimens were contaminated with handpiece oil before acid-etching and 10 were contaminated after acid-etching. The enamel was etched for 15 seconds using 35% phosphoric acid. Following adhesive application, composite resin was bonded using a gelatin capsule technique. Shear bond strengths from the two contaminated groups were compared to bond strengths to uncontaminated enamel obtained from a previous study that was performed by the same group of investigators, using the same facility, materials, and methods. RESULTS: Two-way analysis of variance (ANOVA) showed that the factor "surface contamination" did not have a significant effect on bond strength (p > .542). The type of adhesive and the interaction of adhesive and surface contamination were significant (p < .0001 and p < .003, respectively). When oil was applied before etching, mean bond strengths ranged from 18.0 +/- 4.8 MPa for OptiBond SOLO (Kerr Corp., Orange, California) to 25.3 +/- 5.6 MPa for Tenure Quik with Fluoride (Den-Mat Corp., Santa Maria, California). With oil applied after etching, bond strengths ranged from 18.4 +/- 8.0 MPa for Tenure Quik with Fluoride to 27.4 +/- 5.4 MPa for Single Bond (3M Dental Products, St. Paul, Minnesota). For the same adhesive, comparing uncontaminated and "oil-before-etch" contaminated groups, the only statistically significant difference in bond strengths was for OptiBond SOLO: 21.8 +/- 4.0 MPa (uncontaminated) versus 18.0 +/- 4.8 MPa (oil before etch). Comparing uncontaminated and "oil-after-etch" groups, the only statistically significant difference was for Tenure: 24.5 +/- 5.7 MPa (uncontaminated) and 18.4 +/- 8.0 MPa (oil after etch).
PURPOSE: To evaluate resin bond strength to enamel contaminated with handpiece oil. MATERIALS AND METHODS:Bovine teeth were randomly assigned to six groups of 20 teeth each for treatment with one of six different bonding systems (five one-bottle and one multibottle). For each system, 10 enamel specimens were contaminated with handpiece oil before acid-etching and 10 were contaminated after acid-etching. The enamel was etched for 15 seconds using 35% phosphoric acid. Following adhesive application, composite resin was bonded using a gelatin capsule technique. Shear bond strengths from the two contaminated groups were compared to bond strengths to uncontaminated enamel obtained from a previous study that was performed by the same group of investigators, using the same facility, materials, and methods. RESULTS: Two-way analysis of variance (ANOVA) showed that the factor "surface contamination" did not have a significant effect on bond strength (p > .542). The type of adhesive and the interaction of adhesive and surface contamination were significant (p < .0001 and p < .003, respectively). When oil was applied before etching, mean bond strengths ranged from 18.0 +/- 4.8 MPa for OptiBond SOLO (Kerr Corp., Orange, California) to 25.3 +/- 5.6 MPa for Tenure Quik with Fluoride (Den-Mat Corp., Santa Maria, California). With oil applied after etching, bond strengths ranged from 18.4 +/- 8.0 MPa for Tenure Quik with Fluoride to 27.4 +/- 5.4 MPa for Single Bond (3M Dental Products, St. Paul, Minnesota). For the same adhesive, comparing uncontaminated and "oil-before-etch" contaminated groups, the only statistically significant difference in bond strengths was for OptiBond SOLO: 21.8 +/- 4.0 MPa (uncontaminated) versus 18.0 +/- 4.8 MPa (oil before etch). Comparing uncontaminated and "oil-after-etch" groups, the only statistically significant difference was for Tenure: 24.5 +/- 5.7 MPa (uncontaminated) and 18.4 +/- 8.0 MPa (oil after etch).