S Atsü1, S Berksun. 1. Department of Prosthodontics, Oral Health Center of Ankara, Turkey.
Abstract
STATEMENT OF PROBLEM: Problems with casting and porcelain bonding are encountered when titanium is used in metal-porcelain restorations. The oxidation characteristics of titanium are the main problem. The bonding mechanisms in titanium-porcelain systems are complex and poorly understood. PURPOSE: An in vitro investigation was performed to evaluate the bonding characteristics of 3 titanium-porcelain systems in various firing conditions. MATERIAL AND METHODS: This study evaluated the bonding strength of 3 commercial titanium porcelains fired in a vacuum and in an argon atmosphere to cast and noncast commercially pure titanium, using a 3-point bending test according to DIN 13927 and SEM with energy-dispersive spectrometry analysis. The results were compared with an Ni-Cr alloy and a conventional porcelain that was chosen as a control. RESULTS: The Ni-Cr-conventional porcelain system fired in an argon atmosphere had significantly higher bond strength than the other systems (P<.001). In addition, the bond strength of the titanium-spark erosion-Noritake Ti22 combination, fired in an argon atmosphere, was significantly higher than the other titanium-porcelain groups, which had results similar to those obtained with the vacuum-fired, Ni-Cr-conventional porcelain and argon-fired titanium-cast-Noritake Ti22 groups. On the other hand, the bond strength of the titanium-TiBond and titanium-Vita Titankeramik groups was below the lower limit value in the DIN 13927 standard for the 3-point bending test (25 MPa). Although the results of the Duncan multiple range test showed that firing in an argon atmosphere did not affect the bond strength of the titanium-Vita Titankeramik groups, the titanium-spark erosion-TiBond group, or the titanium-cast-Noritake Ti22 group, argon firing improved the bond strengths of the Ni-Cr-conventional porcelain group, the titanium-cast-TiBond group, and the titanium-spark erosion-Noritake Ti22 porcelain group. It was also found that there were no significant differences between the bond strengths of cast and non-cast titanium groups; an exception was the titanium TiBond groups in which the porcelain was fired in a vacuum. CONCLUSION: The oxide layer produced on titanium was considered to have a potentially adverse effect on titanium-porcelain bonding. It was also concluded that matching the titanium-porcelain combination is the main determinant for optimal bonding. Firing in an argon atmosphere that limited the oxidation of titanium improved the titanium-porcelain bond in some of the groups.
STATEMENT OF PROBLEM: Problems with casting and porcelain bonding are encountered when titanium is used in metal-porcelain restorations. The oxidation characteristics of titanium are the main problem. The bonding mechanisms in titanium-porcelain systems are complex and poorly understood. PURPOSE: An in vitro investigation was performed to evaluate the bonding characteristics of 3 titanium-porcelain systems in various firing conditions. MATERIAL AND METHODS: This study evaluated the bonding strength of 3 commercial titanium porcelains fired in a vacuum and in an argon atmosphere to cast and noncast commercially pure titanium, using a 3-point bending test according to DIN 13927 and SEM with energy-dispersive spectrometry analysis. The results were compared with an Ni-Cr alloy and a conventional porcelain that was chosen as a control. RESULTS: The Ni-Cr-conventional porcelain system fired in an argon atmosphere had significantly higher bond strength than the other systems (P<.001). In addition, the bond strength of the titanium-spark erosion-Noritake Ti22 combination, fired in an argon atmosphere, was significantly higher than the other titanium-porcelain groups, which had results similar to those obtained with the vacuum-fired, Ni-Cr-conventional porcelain and argon-fired titanium-cast-Noritake Ti22 groups. On the other hand, the bond strength of the titanium-TiBond and titanium-Vita Titankeramik groups was below the lower limit value in the DIN 13927 standard for the 3-point bending test (25 MPa). Although the results of the Duncan multiple range test showed that firing in an argon atmosphere did not affect the bond strength of the titanium-Vita Titankeramik groups, the titanium-spark erosion-TiBond group, or the titanium-cast-Noritake Ti22 group, argon firing improved the bond strengths of the Ni-Cr-conventional porcelain group, the titanium-cast-TiBond group, and the titanium-spark erosion-Noritake Ti22 porcelain group. It was also found that there were no significant differences between the bond strengths of cast and non-cast titanium groups; an exception was the titanium TiBond groups in which the porcelain was fired in a vacuum. CONCLUSION: The oxide layer produced on titanium was considered to have a potentially adverse effect on titanium-porcelain bonding. It was also concluded that matching the titanium-porcelain combination is the main determinant for optimal bonding. Firing in an argon atmosphere that limited the oxidation of titanium improved the titanium-porcelain bond in some of the groups.